Bedienungsanleitung Vonroc RH502AC (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778542

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

WWW.VONROC.COM

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2-3.

1. Left/right rotation switch

2. On/Off switch

3. Chuck

4. Lock-on button

5. Function selection switch

6. Auxiliary grip

7. Locking sleeve

8. Depth stop ruler

9. Depth stop button

10. Keyed chuck with SDS shank

11. Chuck key

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Mounting and removing the accessory (Fig. B)

Caution: drills and chisels can get very hot.

Do not use blunt drill bits or chisels.

Immediately sharpen or replace blunt drill

bits or chisels.

Mounting

Insert the accessory into the chuck (3) until a click

can be heard. If needed rotate the accessory a little

to ensure the keyway in the bit ﬁts the chuck well.

Do not slide the locking sleeve (7) to the

rear when inserting bits.

Removing

1. Slide the locking sleeve (7) to the rear.

2. Remove the accessory from the chuck (3).

3. Release the locking sleeve (7).

Optional keyed chuck (Fig. A)

Only use the optional keyed chuck in drilling

mode! The function selector switch (5) must

be set to “drilling mode” (As shown in ﬁg. D

function A).

1. Insert the keyed chuck with SDS shank (10)

into the chuck (3) until a click can be heard. If

needed rotate the keyed chuck a little to ensure

the keyway in the bit ﬁts the chuck well.

2. Open the keyed chuck (10) with the chuck key

(11) by turning the rear sleeve counterclockwi-

se and insert the bit into the chuck opening.

4. Tighten the keyed chuck (10) with the chuck

key (11) by turning the rear sleeve clockwise.

Mounting and removing the auxiliary grip (Fig. A)

Mounting

1. Loosen the auxiliary grip (6) by turning it counter-

clockwise.

2. Mount the auxiliary grip (6) by sliding it over the

chuck (3).

3. Turn the auxiliary grip (6) to the required position.

4. Tighten the auxiliary grip (6) by turning it

clockwise.

Removing

1. Loosen the auxiliary grip (6) by turning it coun-

terclockwise.

2. Remove the auxiliary grip (6).

3. Tighten the auxiliary grip (6) by turning it

clockwise.

Mounting and setting depth stop (Fig. A)

1. The depth stop ruler (8) can be added to the auxi-

liary grip (6) by pushing the dept stop button (9).

2. Keep pushing the depth stop button (9) and

insert the depth stop ruler (8) through the hole

on the side handle ring.

3. Slide the ruler (8) to the desired depth.

4. Loosen the depth stop button (9).

4. OPERATION

Hammer drills require very little operator

pressure. Excessive pressure on the tool

can lead to unnecessary overheating of the

motor, and burning of the driven tool. It also

may happen the drill bit deforms and

cannot be removed from the machine again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc RH502AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info