Bedienungsanleitung Vonroc RH503AC (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778545

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

WWW.VONROC.COM

Setting the operating mode (Fig. A & E)

The drill selection switch (2) and the hammer

selection lever (3) must be set according to the

required operating mode. Refer to the table below

and ﬁgure E to set the required operating mode.

Setting Operating mode (Fig. E)

A) Chipping (chisel function): for chipping and

small demolition jobs.

B) Hammer Drilling (with hammer function): for

drilling in masonry such as brick, concrete and

similar material.

C) Drilling (without hammer function): for drilling

in several materials.

Turn the drill selection switch (2) and the hammer

selection lever (3) to the required position.

User tips

• For large holes, for instance in very hard con-

crete, start using a smaller bit for pilot drilling

ﬁrst, then drill to nominal size.

• Hold the machine ﬁrmly with 2 hands. Be aware

the drill can jam and because of that machine

might suddenly turn (especially when drilling

deep holes).

• Do not apply a lot of pressure on the machine,

let the machine do the work.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/EC

for Waste Electrical and Electronic Equipment and its

implementation into national right, power tools that

are no longer usable must be collected separately

and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest

quality standards and are guaranteed free of

defects in both materials and workmanship for the

period lawfully stipulated starting from the date of

original purchase. Should the product develop any

failure during this period due to defective material

and/or workmanship then contact VONROC directly.

The following circumstances are excluded from this

guarantee:

• Repairs and or alterations have been made

or attempted to the machine by unauthorized

service centers;

• Normal wear and tear;

• The tool has been abused, misused or

improperly maintained;

• Non-original spare parts have been used.

This constitutes the sole warranty made by compa-

ny either expressed or implied. There are no other

warranties expressed or implied which extend

beyond the face hereof, herein, including the im-

plied warranties of merchantability and ﬁtness for

a particular purpose. In no event shall VONROC be

liable for any incidental or consequential damages.

The dealers remedies shall be limited to repair or

replacement of nonconforming units or parts.

The product and the user manual are subject to

change. Speciﬁcations can be changed without

further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc RH503AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info