Bedienungsanleitung Vonroc RS502AC (Seite 7 von 28) (Deutsch, Englisch, Holländisch, Französisch)

764105

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2-3.

1. Handle

2. Lock-on button

3. On/Off button

4. Handle unlock button

5. Auxiliary handle

6. Baseplate

7. Saw blade

8. Chuck

9. Clamping lever

10. Baseplate bolts

3. ASSEMBLY

Before carrying out any work on the

machine, disconnect the mains plug from

the power supply.

Replacing the saw blade (Fig. A, C)

When mounting the saw blade, wear

protective gloves. Danger of injury when

touching the saw blade.

Only use saw blades that correspond with

the characteristic data given in the

operating instructions.

Mounting the saw blade

Make sure the blade holder is free of material

debris (such as splinters of wood or metal).

1. Turn the clamping lever (9) as far to the left as

possible and hold it in this position.

2. Insert the saw blade in the chuck (8). Check

that the saw blade is securely ﬁxed and that the

teeth are pointing downwards.

3. Let go of the clamping lever. Check whether the

saw blade is locked in place.

Make sure to use the right sawblade for the corres-

ponding material. Included with the machine is a

coarse sawblade for wood and a ﬁne sawblade for

metal and plastics.

Removing the saw blade

1. Turn the clamping lever (9) as far to the left as

possible and hold it in this position.

2. Remove the saw blade from the chuck (8).

3. Let go of the clamping lever.

4. OPERATION

Switching on and off (Fig. A)

• To switch on the machine, press the on/off

switch (3).

• To switch the machine to continuous mode,

keep the on/off switch (3) pressed and simulta-

neously press the lock-on button (2).

• To switch off continuous mode, press the on/off

switch (3) again.

• To switch off the machine, release the on/off

switch (3).

Adjusting the base plate (Fig. B)

Due to its movability, the baseplate (6) angle

adapts to the workpiece. Furthermore, the length

of the baseplate can be adjusted depending on the

required sawing depth.

1. Loosen the baseplate bolts (10) using the hex

key provided.

2. Adjust the baseplate (6).

3. Tighten the baseplate bolts (10) using the hex

key provided.

Plunge cutting (Fig. D)

Plunge cutting may only be used on soft materials

such as wood, aerated concrete, gypsum plaster

boards, etc. However, this requires a certain practi-

se and is only possible with short saw blades.

Place the saw onto the workpiece and switch it on.

2. Ensure that the bottom edge of the footplate

rests on the workpiece surface as shown.

3. Slowly saw into the workpiece at an angle, mo-

ving the saw to a vertical position and continue

to saw along the cutting line.

4. Switch the saw off and lift off the workpiece

when the work is complete.

Flush cutting (Fig. E)

Elastic bi-metal saw blades allow you to saw

protruding objects (e,g, water pipes, iron bars, etc,)

nearby the wall.

1. Apply the saw blade directly to the wall and

bend slightly so that the footplate rests against

the wall. Pay attention that the saw blade

always extends beyond the diameter of the

material being worked.

Switch the machine on and saw off the workpiece

keeping constant lateral pressure against the wall.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc RS502AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info