Bedienungsanleitung Vonroc S-CR503DC (Seite 12 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

819184

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

12 WWW.VONROC.COM

Setting the Automatic Shut-Off Pressure (Fig. E)

1. Press the pressure selector (21) on the controle

panel to switch between the different pressu-

re Units ( PSI, BAR, Kpa) until required unit is

displayed.

2. Press the “+”or “-“ on the controle panel until

the desired pressure shows on the display. By

holding the “+”or “-“ you can go up or down

quicker, release “+”or “-“at the dissured pressu-

re.

Note: After 3 seconds the display will ﬂash and

return to areading of “0.0”. This is normal. The set

pressure will be remembered.

3. Move the mode selector I/0/II (20) into the

position ‘I’ to switch the appliance to start the

High pressure.

4. When the item to be inﬂated has reached the

preset valuepressure the unit will automatically

turn off.

Note: You may notice the actual pressure reading

may drop after acouple of seconds. This is normal.

5. To stop the inﬂator at any time, move the mode

selector I/0/II (20) into the position ‘O’ to switch

the appliance off.

Note: If the power switch is turned off, all settings

will be lost and will need to be reentered. This is

asafety feature to prevent the risk of items OVER

INFLATING.

Note: After afew minutes the machine is turned off

automatically. In order to switch on the machine,

press the Pressure selector (21) and the display

(28) will turn on.

Note: When using the Dunlop valve adapter, the

pressure gauge will not display an accurate value

due to characteristics of the valve. When inﬂating

atire, do not use the value on the pressure gauge,

but inﬂate it by checking the status of the tire. If

the tool stops before the tire reaches the desired

air pressure, adjust the pressure value, and then

inﬂate the tire again.

Note: When inﬂating aﬂoating tube, the pressure

gauge will not display an accurate value since

the pressure of ﬂoating tube is less than 20 kPa

(3 PSI). When inﬂating aﬂoating tube, do not use

the value on the pressure gauge, but inﬂate it by

checking the status of the ﬂoating tube.

Using the Inﬂator as aPressure Gauge

Note: This machine has amemory mode in pre-set

function.

Please make sure to switch machine off to remove

memory before using pressure gauge function.

1. In order to switch on the machine, press the Pres-

sure selector (21) and the display (28) will go on.

2. Reattach the hose connected to the valve to be

measured.

3. The digital readout will display the item’spressu-

re.

Removing the connection valve (Fig. D1, D2)

• Removing with or without valve adapter: Open

the clamping lever (7) for the connection valve

(8) and remove from the valve and/or adapter of

the inﬂatable.

• Remove any adapter and close the valve of the

inﬂated item (ball, inﬂatables or tyres)

Note: Air may escape from the valve of the inﬂa-

table when removing the connection valve (8). Be

sure not to remove the connection valve (8) too

quickly. It may be necessary to add extra pressure

to the required pressure, to compensate for the

escaped air.

Storage high pressure hose and valve adapters

(Fig. F, G)

• The high-pressure hose (9) is located in astorage

channel (10) on the back of the machine. Wrap

the high-pressure hose inside the channel.

• The Valve adapters (14, 15, 16) are stored in the

back of the unit inside the valve adapter storage

(19).

LOW PRESSURE, HIGH VOLUME  INFLATA

BLES  SWITCH ‘II’

Inﬂating

Connecting the low pressure hose to the compressor

(Fig. H1)

1. Remove the low pressure hose (11) from the

storage (12).

2. Line up the notches (24) of the hose with the

nubs (23) of the low pressure inﬂator connection

(22) .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S-CR503DC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info