Bedienungsanleitung Vonroc S-GT501DC (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

764168

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

WWW.VONROC.COM

4. Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on the

charger (5) will lighten up and show the charger

status.

The charger has 2 LED indicators (5) which indicate

the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the charger

plug from the outlet and remove the battery from

the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Mounting the Protection guard (Fig. B1)

• Fit the protection guard (10) onto the trimmer

head housing.

• Secure the guard using the screw (11) delivered.

Mounting the guardrail (Fig. B2)

• Squeeze the ends of the guardrail (12) together

and slide into the holes of the trimmer head

housing

• The guardrail can be set in different protection

distances. To adjust the rail, simply press or pull

the rail.

Mounting the front handle (Fig. D1)

• Place the handle (8) on the holder mounted on

the upper shaft.

• Fit the bolt in the hexagon hole and mount the

knob (9) onto the bolt.

Adjusting the front handle (Fig. D2)

• Unscrew the knob (9) slightly and press or pull

the front handle (8) in to desirable position. This

can either be down or upwards and rotatable

around upper shaft.

When using the machine sideways always

use the sidewheel.

Mounting of the side wheel (Fig. E)

• Slide side wheel (13) over the side wheel holder

(14).

Mounting the wire spool (Fig. F1)

Before replacing the spool clean the

machine from any dirt.

• Place the spring (17) into the spool housing

(18). Make sure the wider side of the spring is

placed on the trimmer head.

• Place the spool reel (16) over the spring (17).

Make sure the wires are passed through the

holes inside the housing (18). (Fig. F2)

• Cover the spool reel with the spool cover (15)

and fasten it by turning the cover tightly.

Replacing the spool (Fig. F1)

• Remove the spool cover (15).

• Take out the spool reel (16) but leave the spring

(17) inside.

• Take the new spool reel (GT801AA) and place

it over the spring (17). Make sure the wires are

passed through the holes inside the housing

(18). (Fig. F2)

• Cover the new spool reel with the spool cover

(15) and fasten it by turning the cover tightly.

4. OPERATION

Using the tap and go system (Fig. G)

• When the wire is too short, switch the machine

on and press the tip of the spool reel (19) on

the ground (make sure this is done on a hard

surface).

• This will release the wire in order to get longer.

• The wire will be cut on the correct length auto-

matically by the blade mounted in the protecti-

on guard (10).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S-GT501DC Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info