Bedienungsanleitung Vonroc S2-AG501DC (Seite 12 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

764085

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

WWW.VONROC.COM

the battery has left.

•

When the lights are not burning it means the bat-

tery is empty and must be charged immediately.

Charging the battery with the charger (Fig. C-2)

1. Take the battery (13) from the machine.

2. Turn the battery (13) to upside down position and

slide it onto the charger (17) as shown in Fig. C-2.

3. Push the battery until it is fully pushed into the

slot.

Plug the charger plug into an electrical outlet and

wait for a while. The LED indicators on the charger

(18) will lighten up and show the charger status.

The charger has 2 LED indicators (18) which indica-

the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the char-

ger plug from the outlet and remove the battery

from the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Assembling the protection guard (Fig. E and F)

1. Place the machine on a table with the spindle

(7) facing upwards.

2. Place the protection guard (3) over the machine

head as shown in Figure E making sure the

ridges on the protection guard fall into the

notches of the machine head.

3. Turn the protection guard counter clockwise as

shown in Figure F and clench the release lever

for protection guard (2).

4. You can adjust the position of the protection

guard by releasing the lever (2), adjust the

guard to the desired position and clench the

lever to lock it.

Mounting and removing the wheel disc (Fig. D)

Do not use the machine without the guard.

Only use sharp and undamaged wheel

discs.

• Always use suitable wheel disc for this machine

with diameter Ø 115 mm and a bore from

22.2 mm the thickness of the wheel disc should

be 6 mm for wheel disc for grinding and 3 mm

for wheel disc for cutting, the mounting wheel

disc may not touch the safety guard.

Mounting

1. Place the machine on a table with the protecti-

on guard (3) facing upwards.

2. Mount the ﬂange (9) onto the spindle (7).

3. Place the wheel disc (10) onto the spindle (7).

4. Keep the spindle lock button (1) pressed and

ﬁrmly tighten the clamping nut (11) onto the

spindle (7) by using the spanner (12).

Removing

1. Place the machine on a table with the protecti-

on guard (3) facing upwards.

2. Keep the spindle lock button (1) pressed and

loosen the clamping nut (11) using the spanner

(12).

Remove the wheel disc (10) from the spindle (7).

4. Keep the spindle lock button (1) pressed and

ﬁrmly tighten the clamping nut (11) using the

spanner (12).

Mounting the side handle (Fig. A and G)

• The side handle (8) can be screwed into one of

the three side handle connection points (6).

4. OPERATION

Make sure that the work piece is properly

supported or ﬁxed.

Switching on and off (Fig. B)

• To switch on the machine in continuous mode,

slide the on/off switch (5) to the right and slide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S2-AG501DC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info