Bedienungsanleitung Vonroc S2-SG502DC (Seite 79 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

764114

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

Step 2: Preparing the spray surface

• Cover the area around the to be sprayed area

thoroughly and over a wide area. Any surface

that is not covered properly can unintentionally

be sprayed.

Warning! Be aware of your surroundings

when spraying outside, wind can cause

unintentional spraying of your not covered

surroundings.

• The spray surface needs to be clean, dry, and

free from grease or dust.

• Polished surfaces should be lightly sanded, and

the sanding dust removed.

Step 3: Filling the paint container

• Remove the container (11) from the Spray unit.

• Fill the container with to be sprayed material to

a maximum of 800ml.

• Adjust the riser pipe (23) according to the

position you are going to use the spray gun in.

Spraying angle up like show in Fig. F. spraying

angle down like show in Fig. G

• Make sure the gasket and riser pipe (23) are

properly installed in the container cap (10).

Tighten the container (11) onto the container

cap (10).

Step 4: Test and adjust the spray jet effect, spray

volume and spray ﬂow. (Fig. A + B)

Note: Before starting to spray the work surface, it

is advisable to make an initial test by spraying a

small area on scrap material.

Tip! With low-viscocity use the smaller nozzle and

with high-viscocity use the bigger nozzle.

1. Choose the jet effect: Horizontally

•

or verti-

cally

•

. By turning the nozzle adjusting ring (16)

left or right.

2. Adjust the spray volume with Spray volume

adjusting wheel (9) by turning it to the left – to

reduce the volume, to the right + to increase.

Note: Low volume is advised for smaller object

or surfaces. High volume is advised or bigger

surfaces.

Tip: We recommend starting at the minimum

setting.

3. Adjust the spray ﬂow by using the spray ﬂow

adjustment knob(2): turn the knob to the left

to reduce the ﬂow, to the right to increase the

ﬂow. Note: The thinner the paint the lower the

ﬂow should be, when using thicker paint make

sure to use a higher ﬂow.

Tip: Several light layers rather than one thick layer

will help prevent the paint running.

4. Aim the spray gun to the to be sprayed surface

and pull the trigger (1). Hold the front of the

spray gun around 20-30 cm away from the to

be sprayed surface. Make long arm movements

rather than short wrist movements like show in

ﬁgure H. The most suitable method of surface

spraying is with a cross-pattern, starting with

horizontal passes and ﬁnishing with light verti-

cal passes. See ﬁgure J.

5. Release the trigger (1) to stop the spraying.

Check Spray Pattern Quality A good spray pat-

tern is evenly distributed as it hits the surface, if

not (add highest spray ﬂow) check the following:

- Spray tip may be worn.

- A smaller spray tip may be needed.

- Material may need to be thinned.

7. Adjust the Jet effect (step A), spray volume

(step B) and Spray ﬂow (step C) depending on

the paint, object- surface to be sprayed and

desired coverage. Repeat steps D to H when not

satisﬁed with the test results.

Always let the paint/varnish/stains dry according to

the recommend dry time of the spray material for

applying multiple coats. Several light coats rather

than one thick coat will help prevent the paint

running.

5. VEDLIGEHOLDELSE

Før rengøring og vedligeholdelse skal du

altid slukke for maskinen og trække

netstikket ud af kontakten.

Rengøring efter hver brug

Det er vigtigt, at sprøjtepistolen rengøres grundigt

efter hver brug. Hvis den ikke rengøres, vil det

næsten helt sikkert resultere i blokeringer, og den

fungerer muligvis ikke næste gang. Garantien dæk-

ker ikke en sprøjtepistol, der ikke er blevet rengjort

korrekt af brugeren.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S2-SG502DC Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info