Bedienungsanleitung Vonroc S2_PM506DC (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

778568

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

WWW.VONROC.COM

3. ASSEMBLY

Before any work on the power tool, remove

the battery.

The battery must be charged before ﬁrst

use.

Inserting the battery into the machine (Fig. D)

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

1. Insert the battery (11) into the base of the ma-

chine like shown in Fig. D.

2. Push the battery further forward until it clicks

into place.

Removing the battery from the machine (Fig. D)

1. Push the battery unlock button (12).

2. Pull the battery out of the machine like shown

in Fig. D.

Checking the battery charging status (Fig. E)

• To check the battery charge status, push the

button (13) on battery shortly.

• The battery has 3 lights indicating the charge

level, the more lights that burn, the more charge

the battery has left.

• When the lights are not burning it means the bat-

tery is empty and must be charged immediately.

Charging the battery with the charger (Fig. E)

1. Take the battery (11) from the machine.

2. Turn the battery (11) to upside down position

and slide it onto the charger (15) as shown in

Fig. E.

3. Push the battery until it is fully pushed into the

slot.

4. Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on the

charger (14) will lighten up and show the char-

ger status.

The charger has 2 LED indicators (16) which indi-

cate the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the char-

ger plug from the outlet and remove the battery

from the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Assembling the two-part whisk (Fig. A)

1. Screw the Whisk shaft (5) onto the Whisk pad-

dle (6)

2. Tighten both parts securely

Replacing the whisk (Fig. C)

Always remove the battery before mounting

an accessory.

Use only whisks conform the speciﬁed diameter.

Always use a whisk that is suitable for the material

to be mixed/stirred. Using an unsuitable mixer bar

can unnecessarily overload both the machine and

yourself.

Mounting the whisk

1. Screw the assembled whisk into the tool holder

(4) in clockwise direction as far as possible.

2. Tighten the whisk into the tool holder using the

supplied spanners (10). To do so, hold the tool

holder (4) using one of the supplied spanners,

and use the second spanner to tighten the

assembled whisk.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S2_PM506DC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info