Bedienungsanleitung Vonroc S_SG503DC S2_SG503DC (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778550

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

WWW.VONROC.COM

7. Reload lever

8. LED work light switch

9. Safety tip

10. Belt hook

11. Adjustment knob

12. Battery LED indicators button

13. Battery LED indicators

14. Charger

15. Charger LED indicators

3. ASSEMBLY

Before any work on the power tool, remove

the battery.

The battery must be charged before ﬁrst

use.

Inserting the battery into the machine (Fig. B)

Ensure that the exterior of the battery is

clean and dry before connecting it to the

charger or machine.

1. Insert the battery (2) into the base of the

machine as shown in Fig. B.

2. Push the battery forward until it clicks into place.

Removing the battery from the machine (Fig. B)

1. Push the battery unlock button (3).

2. Pull the battery out of the machine like shown

in Fig. B.

Checking the battery charging status (Fig. C)

• To check the battery charge status, push the

button (12) on battery shortly.

• The battery has 3 lights indicating the charge

level, the more lights that burn, the more

charge the battery has left.

• When the lights are not burning it means

the battery is empty and must be charged

immediately.

Charging the battery with the charger (Fig. C)

1. Take the battery (2) from the machine.

2. Turn the battery (2) to upside down position and

slide it onto the charger (14) as shown in Fig. C.

3. Push the battery until it is fully pushed into the

slot.

Plug the charger plug into an electrical outlet and

wait for a while. The LED indicators on the charger

(15) will lighten up and show the charger status.

The charger has 2 LED indicators (15) which

indicate the status of the charging process:

Red LED

Status

Green LED

status Charger status

Off Off No power

Off On

Standby mode:

- No battery is inserted or,

- Battery inserted but charging

has ﬁnished

On Off Battery charging in progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the charger

plug from the outlet and remove the battery from

the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Application (Fig. D)

For this tool, use one of the following length for

staples or nails:

• Staples: Type 55: 15-25mm

• Nails: Type 47: 15, 20, 25, 30 or 32mm

Loading the nails or staples (Fig. D-G)

• Choose the correct nail or staple for the job.

• Place the tacker (1) on its side with the battery

(2) pointing to the right, like show in ﬁg. E.

• Open de cartridge shaft (6) by slightly pressing

the reload lever (7).

• Pull the reload lever (7) to the right to open the

cartridge shaft (6).

For nails:

• Place the nails at the top of the cartridge shaft

(6). Like shown on the label of the cartridge

shaft, see example ﬁg. F.

For staples:

•

Place the staples at the bottom of the cartridge

shaft (6). Like shown on the label of the cartridge

shaft, see example ﬁg. G.

• Slide the cartridge shaft (6) back until it clicks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S_SG503DC S2_SG503DC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info