Bedienungsanleitung Vonroc SG503DC (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778549

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

9WWW.VONROC.COM

Before loading the tacker, make sure to

remove the battery form the machine.

Only load fasteners of the same type and

length. Do not load staples and nails at the

same time. Do not mix fasteners of varying

lengths.

4. OPERATION

Using the work light (Fig. A)

• Press the LED work light switch (8) to turn on

the work light (4).

•

The work light will be activated for 10 seconds

and helps to improve visibility of the working

area.

Belt hook

The machine is equipped with a belt hook (10) for

hanging the machine to your belt during use.

• When delivered, the belt hook (10) is assembled

to the machine.

• It can easily be removed by removing the screw

on the hook and taking it off.

Adjusting impact power (Fig. A)

• Increase impact: rotate the adjustment knob

(11) clockwise.

• Reduce impact: rotate the adjustment knob

(11) anti-clockwise.

Driving staples/nails (Fig. A)

• Place the safety tip (9) ﬂat on the material to

be fastened at the spot where the staple or nail

should be located.

• Hold the front and rear part of the machine and

press the machine ﬁrmly against the material.

• Pull the trigger (5) to drive the staple/nail, then

release your ﬁnger from the trigger before

lifting the safety tip (9) from the material.

• If the staple/nail is driven too deep or too

shallow, adjust the impact power.

Warning! The safety of the machine will be

lifted when pressure is applied to the safety

tip (9) on the bottom of the machine.

Always make sure the tacker mouth is in

direct contact with the material when

pressing the trigger.

The tool may rebound and produce a loud

sound because of the impact it operates

with. Keep this in mind. For long nails and

staples this may cause incorrect stapling or

nailing. Adjust the impact power accordingly

and apply backpressure to the machine to

prevent incorrect stapling or nailing.

5. MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

This machine has been designed to operate over

a long period of time with a minimum of mainte-

nance. Continued satisfactory operation depends

upon proper machine care and regular cleaning.

Malfunction

In case a staple or nail is jammed in the tool, follow

the procedure below:

• Remove the battery from the machine.

• Place the tool down on its side.

• Press the cartridge shaft release lever (7), pull

the cartridge shaft (6) backward and unload the

staples or nails strip.

• Remove the clogged staple/nail from the car-

tridge.

• Reload the staples/nails and push the cartridge

shaft back in place until it clicks.

• Insert the battery into the machine.

• Test the machine on a piece of scrap.

Operating tips:

• WARNING! Nails or staples must be driven

straight into the material. Do not tilt the machine

during operation.

• Do not operate the machine without staples or

nails. This will shorten the service life of the

machine.

• Should nails or staples jam frequently, have ma-

chine serviced by an authorized service centre.

• If the head of the nails or staples remains above

the workpiece surface, press the machine head

ﬁrmly against the workpiece and try again.

If there is no improvement in the rework, the

chosen material may not be suitable for the tool

or the impact power may need adjusting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc SG503DC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info