774092
7
Zoom out
Zoom in
Vorherige Seite
1/82
Nächste Seite
11
English
10 English
HOW TO USE
4. To adjust timer, repeat Step Three.
5. To cancel timer, repeat Step Three and
set timer for 0.
CORD MANAGEMENT
1. Wrap cord around Air Accelerator,
located on back of unit. Secure cord with
three clips located at 2, 6 and 10 o'clock
positions.
1. Touch to power on.
Your circulator returns to last saved
memory setting.
2. Select desired speed by pressing -/+.
Press and hold -/+ to adjust speed up
or down in 5 speed increments. Speed is
indicated by number shown on Speed/
Timer Indicator Display.
3. Press to activate timer. The
illuminates and Speed/Timer Indicator
Display flashes 0 to indicate Timer
Adjustment Mode. While in this mode,
select amount of time in one-hour
intervals by pressing -/+. After three
seconds, flashing stops and display shows
hours to indicate timer is set. The display
returns to the last speed selected. Touch
to quickly tell how many hours are
remaining on the timer.
REMOTE CONTROL
Screwdriver required.
1. For battery replacement, the remote
requires one coin style 3V CR2032 battery.
Always use the correct size and grade of
battery for this product.
2. To replace battery, open battery door on
the back side of the remote control (you
will need to loosen the small screw on
door using a #1 Phillips screwdriver). If
necessary, clean the battery contacts and
also those of the device prior to battery
installation. Remove any plastic protection
from the battery and place it in the
remote with the + side facing out. Ensure
the battery is installed correctly with
regard to polarity. Replace the battery
door and screw.
Note: Remove battery from the remote
control when not in use for an extended
period of time and always remove dead
battery immediately and replace with fresh.
Do not store dead battery in remote.
The remote control functions are the same as
the control panel on the circulator.
The remote requires a line-of-sight path to
allow for the signal to be received by the
circulator. Point the remote control at the
display panel for best reception.
Your circulator remote includes (1) coin style 3V CR2032 battery. Battery comes pre-installed. Remove battery pull tab before first use.
POWER
TIMER
SPEED/TIMER
ADJUSTMENT -/+
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Vornado 6303DC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info