Bedienungsanleitung Voss Proficut (Seite 6 von 10) (Englisch)

766094

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

18 19

During clipping: Reset the tension screw by a further quarter-turn, if the blades do not cut sufficiently anymore. The

blades are blunt and must be resharpened, if resetting is unsuccessful. Be careful not to overdo the clipping tension.

Slightly reset the clipping tension occasionally during clipping. Hairs can accumulate between the shear blades, if you

clip with insufficient clipping tension. This negatively influences the clipping procedure or even makes it impossible! The

shear blades must be disassembled, cleaned, oiled and reassembled according to item 4.2 if this is the case. Avoid too

high plate pressure, since this increases temperature and wear. The factory has fully adjusted shipped shears for clipping.

3.3 Correct clipper head oiling

The most frequent error cause for a non-satisfactory clipping result as well heating up of the clipper is want of lubricati-

on. A light oil film on the shear blades is essential for an optimal clipping result as well as to increase the service life of

the shear blades and machine. All other moving parts of the clipper head must also be well lubricated. Drip oil on the

shear blades and into the oil opening of the clipper head

(fig. 1 + 2) every 10 minutes, so that these do not run dry. Only use our special clipper machine oil.

3.4 Turning on/off

The slide switch has two positions (fig. 3, shows position 0)

• Position 1: Machine is turned on

• Position 0: Machine is turned off

Check the switch position before plugging in. The switch must be in position 0. Only use the slide switch for turning the

machine on and off.

4. Maintenance

Turn the machine off and pull the power supply plug before beginning maintenance work. Always disconnect the power

supply first before working on the shear blades/clipper head. Do not touch the shear blade area even if the machine is

switched off as long as the clipper is still connected to the current supply.

4.1 Cleaning

After having finished clipping wipe the oil off the machine, clipping head and shear blades with a dry cloth and remove

the hairs with a dry paintbrush or brush. Then lightly oil all parts to prevent rusting. Note that even the smallest rust

spots impair clipping considerably or even render this completely impossible.

4.2 Shear blade assembly

The shear blade set consists of a lower plate and an upper plate. When assembling the shear blades pay attention that

the correct plates lie on top of one another.

Assemble the blades as follows:

• Loosen the clipper tension screw and put the clipper onto a hard surface, so that the blade fastening screws look

upwards.

• Loosen the blade fastening screws and remove the two old blades.

• Ensure that the new shear blades are clean. Pay particular attention to the fact that the sharpened areas are dirt-free;

it is otherwise impossible to achieve a satisfactory clipping result even with newly sharpened shear blades.

• Put the new upper plate into the swing head guides and then put some drops of oil onto the sharpened areas.

• Now push the new lower plate in between the released screws (fig. 4).

• As soon as you have adjusted the shear blades, fixate the lower plate position and tighten the blade

fastening screws.

4.3 Resharpening the blades

Resharpening shear blades correctly is only possible with special machines and by the specialised trade. Only use sharp

shear blades. Defective blades with broken off teeth or blunt blades must be replaced.

4.4 Storing the clipper

Between clippings always keep the well-cleaned and lubricated clipper in the supplied case in a dry location, which is

not accessible to children. Do not switch the machine on, if you suspect that liquids could have entered. There is danger

of an electric shock or short-circuit. Have the machine serviced!

4.5 Cleaning the clipper head

Clean the clipper head after a few days use. Dismantle the cutter plates. Release both screws and remove

the clipper head from the drive unit. Now clean the interior of the clipper head and the other components thoroughly

with a brush and a paintbrush. Lubricate the clipper head according to 3.3 after careful assembly.

5. Repairs

5.1 Introduction

You can read up on troubleshooting measures on the next page. Only authorised technical personnel may carry out

troubleshooting measures marked with an *.

5.2 Malfunction lists

Contact an authorised service department to repair not listed malfunctions.

6. Environmental protection and disposal

The user is responsible for the appropriate disposal of the shear blades and clipper after their service

life. Observe your local pertinent regulations. Do not dispose of the appliance with domestic refuse.

As part of the EU Directive governing the disposal of electric and electronic appliances, the appliance

is accepted free of charge by local waste collection points or recycling centers. Correct disposal will

ensure environment protection and prevent a potential harmful impact on people and the environ-

ment.

18192=BA_FarmClipper4_148x210_0816.indd 19 25.08.2016 14:40:17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Voss Proficut Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Voss Proficut

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info