Bedienungsanleitung Voxx APS-45N Prestige (Seite 4 von 8) (Englisch)

583708

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

128-8602

4 of 8

GREEN/BLACK Wire: Immediate, 300mA Duration of Transmit, Channel 3 OutputThe Green/Black wire supplies a 300mA

switched output whenever Channel 3of the receiver is accessed. Pressing A combination of thetransmitter Lock/UnLock

buttons simultaneously will access Channel 3 and will remain active for as long as the transmitter button(s) is held. This

is a low current output and must be connected to a relay to supply power to the device you intend to control. Connect

Green/Black Trace wire to terminal #86 of a VF45F11 P&B relay or equivalent. Connect terminal #85 of the relay to a fused

+ 12 volt source. Connect the common, normally open, and normally closed contacts of the relay to perform the selected

function of the Channel 3 output.

ORANGE Wire: Ground When Armed Output

This wire provides a 300mA ground output when the keyless entry is locked to control the optional starter inhibit relay.

Connect the Orange wire to terminal #86 of a standard SPDT relay. Connect terminal #85 of the relay to an ignition wire

in the vehicle that is +12VDC when the ignition key is turned to the on and start positions and off when the key is in the off

position. Locate and cut the low current starter solenoid wire found at the vehicle's ignition switch harness. This wire will

have +12VDC when the ignition key is moved to the start (crank) position and will have 0 volts in all other key positions.

Connect one side of the cut wire to terminal #87a of the relay. Connect the other side of the cut wire to terminal #30 of the

relay.

DOOR LOCK/UNLOCK CONTROL HARNESS

3PIN White Plug w/3 Wires; RED, GREEN, & RED/BLACK

The Red and Green Door Lock/Unlock output wires provide either a momentary pulsed ground (-) or a momentary pulsed

+12VDC (+) output for controlling a vehicle's power door lock/unlock circuit. To better understand this, refer to the table

below:

The Red w/Black trace wire will provide a pulsed ground only and will only provide an output when the lock/unlock button

of the transmitter is pressed a second time after a first unlock command was issued. This is used for second step unlock

or all doors unlock in a two step circuit. In this arrangement, Red is used to control the drivers door unlock relay and the

Red/Black will be used to control unlock of all other doors.

3 Wire Ground Switched Signal Step Door Locks

In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red

wire to the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay.

The green wire provides a ground pulse during disarming, or the pulsed ground unlock output. Connect the green wire to the

wire that provides a low current ground signal from the factory door unlock switch to the factory door lock control relay. Red/

Black Not Used.

3 Wire Ground Switched 2 Step Door Locks

In this application, the red wire provides a ground pulse during locking, or the pulsed ground lock output. Connect the red

wire to the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay.

The green wire provides the first ground pulse during unlocking, or the drivers door pulsed ground unlock output.

Connect this wire to the drivers door unlock relay that requires a low current ground signal to unlock only the drivers door.

If the vehicle does not have a separate drivers door relay, one will have to be added. Locate the drivers door unlock motor

wire and cut it at a convenient location to allow wiring of an optional relay. Connect the door side of the cut wire to terminal

30 of the optional relay added. Connect the vehicle side of the cut wire to terminal 87a of the optional relay added. Connect

the green wire of the 3 pin harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay

added to a fused constant + 12 volt source. Most vehicles door lock/unlock motor legs rest at ground and switch +12 volts

to the door lock/unlock motor legs for operation. If this is the case in the vehicle you are working on, connect the remaining

terminal 87, to a fused + 12 volt source. In the rare instance that the vehicle door lock/unlock motor legs rest at + 12 volts

and switches ground to the door lock/unlock motors, connect the remaining terminal 87, to chassis ground.

The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second time

after unlocking the driver's door. Connect the Green/Black wire to the wire that provides a low current ground signal from

the factory door unlock switch to the factory door lock control relay.

3 Wire Positive Switched Door Locks

In this application, the red wire provides a positive pulse during unlocking, or the pulsed + 12 volt unlock output. Connect

Wire Color Function Polarity

Red Lock Ground (-)

Red Unlock Positive (+)

Green Lock Positive (+)

Green Unlock Ground (-)

Green/White 2nd Unlock Pulse Ground (-)

Red/Black

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Voxx APS-45N Prestige Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info