809795

VTech RM7766HD Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Frequency Baby unit: 2412 - 2472 MHz
Channels 13
LCD 7’’ Colour LCD
(IPS 1280x800 pixels)
Nominal effective range Actual operating range may vary according to environmental conditions
at the time of use.
Power requirement Baby unit power adaptor: Output: 5V DC, 1000mA.
Parent unit power adaptor: Output: 5V DC, 2A.
Parent unit battery: 3.7V 5000mAh, 18.5Wh Lithium-ion battery
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc.
All rights reserved. 12/22. RM7766-XHD_UK_EN_QSG_V4
Technical specications
RM7766HD
7” Smart Wi-Fi 1080p
Pan & Tilt Monitor
Quick start guide
Status icons
Direct mode
The parent unit and baby unit
connect to each other directly.
Red bars indicate no connection.
Router mode
The parent unit and baby unit
connect via the Wi-Fi network.
The red icon on the baby unit or
parent unit, indicates no connection
between the respective unit(s) and
the router.
Black and white night vision is
activated.
Motion detection alert is turned on.
Sound detection alert is turned on.
Melodies or soothing sounds are
playing.
Night light is on.
Auto night light brightness is
activated.
Parent unit speaker is muted.
Temperature alert is turned on.
21
21 Temperature (Blue: lower than 20°C;
White: between 20-24°C;
Orange: higher than 24°C)
Battery level indicator
Low battery indicator.
The applied nameplate is located at the bottom of the baby
unit’s base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above
2 metres.
4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be
used as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water, for example, near to a
bath, sink, swimming pool or shower.
7. CAUTION:
Use only the battery provided. There may be a
risk of explosion if a wrong type of battery is used for the
parent unit. The battery cannot be subjected to high or low
extreme temperature and low air pressure at high altitude
during use, storage or transportation. Disposal of battery
in fire or a hot oven, mechanically crushing or cutting the
battery can result in an explosion. Leaving the battery in an
extremely high temperature surrounding environment can
result in an explosion or the leakage of flammable liquid of
gas. Battery subjected to extremely low air pressure may
result in an explosion or the leakage of flammable liquid or
gas. Dispose of used batteries according to the instructions
.
8. Use only the power adaptors included with this product.
Incorrect power adaptor polarity or voltage can seriously
damage the product.
Power adaptor information:
Parent unit output: 5V DC 2A
VTech Telecommunications Ltd.
Model: VT07EUK05200 (UK)
Baby unit output: 5V DC 1A
VTech Telecommunications Ltd.
Model: VT05EUK05100 (UK)
Rechargeable battery information:
3.7V 5000mAh, 18.5Wh Lithium-ion battery
Zhuhai Great Power Energy Co., Ltd.
Model: GSP806090-5Ah-3.7V-1S1P
9. The power adaptors are intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet should
be installed near the equipment and should be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Do not modify the power adaptors or replace with other
adaptors, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply in your home, consult
your dealer or electricity supply provider.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand
or other unstable surfaces.
17. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back
or bottom of this product are provided for ventilation. To
protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a
bed, sofa or rug. This product should never be placed near
or over a radiator or heat source.
18. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage points
or create a short circuit. Never spill liquid of any kind on the
product.
19. To reduce the risk of electric shock, do not isassemble
this product, but take it to an authorised service
acility. Disassembling or removing parts of the
product other than via the battery door may expose
you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
20. You should test the sound reception every time you turn
on the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the
product has never been used before purchase, reset
the baby monitor periodically by powering off and then
powering on the units, and power off the baby monitor if
you are not intending to use it for some time.
23. The small parts of this monitor can be swallowed by
babies or small children. Keep these parts out of reach of
children
24. Children should be supervised to ensure that they do not
play with the product.
25. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 0oC
and 40oC.
2. Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as
bright sunshine or fire.
4. Mishandling batteries can cause burn, fire or explosion
hazards.
5. Warning—Strangulation Hazard—Children
have STRANGLED in cords. Keep this cord out
of the reach of children (more than 0.9m away.
Do not
remove warning label on the adaptor
cord
.
6. Never place the baby unit(s) inside the baby’s crib or
playpen. Never cover the baby unit(s) or parent unit with
anything such as a towel or a blanket.
7. Other electronic products may cause interference with
your baby monitor. Try installing your baby monitor
as far away from these electronic devices as possible:
wireless routers, radios, cellular telephones, intercoms,
room monitors, televisions, personal computers, kitchen
appliances and cordless telephones.
For better security and more stable connectivity, this baby monitor requires
connecting to a Wi-Fi network and operating in Router mode connection.
Direct mode
Your baby monitor parent unit and baby unit connect to each other in Direct mode by default,
which allows you to immediately stream video out of the box.
It is NOT recommended to continue using Direct Mode connection after initial installation.
You may experience reduced signal strength
if your parent unit and baby unit are far apart,
or there are obstructing factors, such as
internal walls, between them. You have to set
up Router mode to connect the units via your
home Wi-Fi network to improve the
connection between your parent unit and
baby unit.
Router mode
You are required to set up your monitor
in Router mode to enjoy live video
streaming via your parent unit with an
enhanced connection. Router mode
is the recommended mode for stable
connectivity.
Router mode uses your home Wi-Fi
network to connect your video monitor. It
supports live video streaming through the
parent unit and smartphone app.
If you want to stream live video remotely
with your mobile device, download and
install the MyVTech Baby Pro mobile app.
With the mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD
video monitor system. It serves as a communicating channel between your baby unit and mobile
device, allowing you to monitor and/or control your baby unit wherever you are. For more
details, see Download app for mobile access section in this quick start guide.
Note
• When both parent unit and app are viewing the camera simultaneously,
the video quality will be optimised to deliver the best possible viewing result.
Overview
What’s in the box
Connect, charge and power on the baby monitor
x 2 x 2
Quick start guide
Your baby monitor package contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
How the system works Parent unit icons
For mobile access:
MyVTech Baby Pro mobile app
Network Wi-Fi
Wi-Fi router 2.4GHz 802.11 b/g/n
Internet connection 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload
bandwidth per baby unit
Requirements
Main
Menu Options
Night light
• Turn on or turn off night light.
• Select a night light colour.
• Adjust night light brightness.
• Set a night light timer.
Melodies and soothing sounds
• Select play all melodies, or play
one of the five melodies and five
soothing sounds.
• You can also set the timer to stop
playing after 15, 30 or 60 minutes,
or playing non-stop.
Alerts - Sound, motion and temperature
• Turn on/off sound detection,
motion detection, and
temperature alerts.
• Select the sound and motion
sensitivity level.
• Turn on/off Auto Wake-up .
• Select maximum and minimum
temperature for alert range.
• Set the temperature format to
Fahrenheit (oF) or Celsius (oC).
Parent unit settings
• Adjust parent unit screen brightness.
• Adjust Low Battery Alert Tone
volume.
• Adjust No Link Alert Tone volume .
Baby unit settings
• Turn on/off Night Vision.
• Turn on/off baby unit Status LED.
• Adjust baby unit speaker volume.
General settings
• Connect to home Wi-Fi network.
• Connect mobile phone.
• Reset Settings to factory default.
• Software Update.
Connect the baby monitor
• The rechargeable battery in the parent unit is built-in.
• Use only the power adaptors supplied with this product.
• Make sure the parent unit and the baby unit are not connected to an electronically controlled electric outlet.
• Connect the power adaptors in a vertical or floor mount position only. The adaptor prongs are not
designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling,
under-the-table, or cabinet outlets. Otherwise, the adaptors may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adaptor cords are out of reach of children.
Charge the parent unit battery before use
The parent unit operates on an internal rechargeable battery or AC power. To continuously
monitor your baby, keep the parent unit connected to AC power.
• Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When
the parent unit battery is fully charged, the battery icon becomes solid .
• The standby time varies depending on your actual use.
The parent unit turns on automatically after connecting to the power socket, and the
welcome screen appears. You can press Power o turn the parent unit on or press and
hold to turn it off.
The battery icon indicates the battery status (see the following table).
Battery indicators Battery status Action
alert displays on the parent unit
screen, and the battery icon shows
empty , with the LED light
flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without
interruption
(about 30
minutes).
The battery icon becomes solid . The battery is fully
charged.
To keep the battery
charged, connect it to AC
power when in use.
Slide the switch to ON to power on your baby unit.
• When powering up, the baby unit’s status LED turns on.
It will turn off after a while and remains off.
• The status LED is set to off by default. If you want to
keep the LED on, press MENU, then go to
> Status LED and turn it on.
NOTE:
Camera lens and surface may get
warm during normal operation.
WARM
WARM
Parent unit overview
1LINK LED light
• On when the parent unit is linked to the
baby unit.
• Flashes when the link to the baby unit
is lost.
2 LED light
• On when the parent unit is connected to
AC power, and the battery is charging.
• Flashes when the parent unit battery is
low and needs to be charged.
33- level sound indicator light
• Green: low sound level is detected by
the baby unit.
• Green and amber: moderate sound
level is detected by the baby unit.
• Green, amber and red: high sound level
is detected by the baby unit.
4TALK /
• Press and hold to talk to the baby unit.
• While in a sub-menu, press to exit.
5MENU | SELECT
• Press to enter the main menu.
• While in a menu, press to choose an
item, or save a setting.
6 | | | Arrow keys
• Press to navigate leftward, upward,
rightward or downward, within the
main menu and sub-menus.
• Press to move the baby unit camera
leftward, rightward , upward or
downward.
7 |
• Increase or decrease parent unit
volume.
8 Zoom
• Press to zoom in/out.
• While in a sub-menu, press to view the
help menu.
9 Power | LCD ON/OFF
10 Microphone
11 Antenna
12 Speaker
13 Power jack
14 RESET
• Force reboot the parent unit.
15 Stand
Mobile access
Connecting Wi-Fi to
enhance local access
2
1
3
4
5
6
7
8
9
10
15
14
13
12
11
Important safety instructions
Raise the parent unit
antenna for better
reception
Press the Power key
1Light sensor
2Camera lens
3Infrared LEDs
• Allow you to see clearly in a dark environment.
4Microphone
5Night Light
6 Night Light Control Key
• Go to Night Light section to learn more.
7LED indicator
• Steadily on, then off, when the baby unit is
connected to the parent unit.
• Flashes when the baby unit is connecting with
the parent unit, or the link to the parent unit
has lost.
8ON/OFF switch
• Power it on or off.
9Speaker
10 Temperature sensor
11 Power jack
12 Wall mount slots
13 PAIR
• The parent unit and baby unit provided are
already paired.
• Reset the baby unit to factory default.
1. Press and hold PAIR key until you hear a
beep sound.
2. Release the PAIR key, and then press the
PAIR key again five times until you hear
another beep sound.
3. The baby unit will sound another beep
when the reset completes. Then, the
baby unit will reboot.
7
8
9
10
4
6
5
2
11
12
13
1
3
7
8
9
10
4
6
5
2
11
12
13
1
3
7
8
9
10
4
6
5
2
11
12
13
1
3
Baby unit overview
Basic operation
Talk to your baby via the baby unit
1. Press and hold the TALK key.
2. When the icon displays on
screen, speak to your parent unit.
Your voice is transmitted to the
baby unit.
3. When finished talking, release
the TALK key to hear your baby
again.
Turn on/off baby unit's status LED
Turn on or turn off the baby unit status LED
indicator. Go to:
> Status LED.
Zoom
Press to zoom in or out in a fixed
zoom sequence. indicates that the
image is magnified 3 times.
Adjust speaker volume
Press | to adjust the parent unit
speaker volume level received from the
baby unit.
After powering up your video monitor, the parent unit streams live video in direct mode.
We recommend you follow the instructions on screen to set up home Wi-Fi network
with your monitor for functionality enhancements and mobile access. See Auto software
and rmware update and Download app for mobile access in this quick start guide.
Use the menu
Press MENU on the parent unit to enter the
main menu, choose a menu item, or save a
setting. You can use the parent unit menu
for advanced settings or operations, such
as to play or stop the baby unit lullaby, or
adjust the baby unit sound sensitivity.
While in the menu:
• Press | | | to scroll among the
menu options.
• Press SELECT to select an item.
• Press TALK to return to the live video.
• Press to go to the Help & info page.
To restore to the default settings or reset the Wi-
Fi connection, you can reset the parent unit by
pressing the RESET key at the back of the unit.
Insert a pin into the RESET hole on the back of
the parent unit, and then gently press the key
inside.
Turn on/off the parent unit screen
You can turn on or turn off the parent unit
screen without powering off the unit. You
will still hear sounds from the baby unit.
• Press | LCD ON/OFF on the parent unit
to turn off the screen.
• Press any key on the parent unit to turn
the screen on again.
Muted
Press and hold
Press the Power key
b) From app store
1. Browse the App Store or the Google Play store .
2. Search for the mobile app with the keyword “myvtech baby pro“.
3. Download and install the MyVTech Baby Pro mobile app to your mobile device.
OR
Scan the QR code on the right to get the app.
• Make sure your mobile device meets the minimum
requirement for the mobile app.
Minimum requirement
The mobile app is compatible with:
• AndroidTM 6.0 or later; and
• iOS 12 or later.
a) From parent unit
• Before installing the app, please connect your baby monitor to your Wi-Fi network.
Press MENU on the parent unit, go to , and select “Congure Wi-Fi”to set up the
Wi-Fi connection.
1. Press MENU.
2. Go to > Connect Mobile Phone.
3. Scan the QR code in the parent unit to download the app into your mobile
device.
1
Download app for mobile access
App installation
In your mobile device:
1. Tap to run the mobile app, and then create a user account.
2. We recommend that you use common webmail services, such as Google
Gmail for registration of your user account. Check your email (and Spam
folder), and activate your new camera account via the email link, then sign in to
your account.
2Set up user account
Add camera
3
Follow the instructions in the mobile app to pair the camera. Tap , then Add Camera
in the mobile app to get started.
Local access
Local access, for
start up quick view
and setup stage.
Scan to learn more
on improving
connectivity.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech RM7766HD wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info