809755

VTech VM320 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not
be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular
times thereafter.
Caution
• For hearing protection, make sure the parent unit is more
than 3 feet (1 metre) away from both baby units. If you hear
any high-pitched noise, move the parent unit further until
the noise stops. You can also press VOL on the parent unit
to reduce the noise.
1. Make sure your baby unit and parent unit are on.
2. The parent unit displays images from the baby unit.
• Speak towards the microphone of the baby unit. You will hear the sound at the parent unit.
Note
• When the parent unit displays No link to Camera, and the POWER LED light flashes, move the parent
unit closer to the baby units (observe the minimum distance of 3 feet / 1 metre).
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby units.
Positioning the baby monitor
Caution
• Keep the baby unit out of reach of your baby. Never place or mount the baby unit inside the baby’s cot
or playpen.
Note
• To avoid interference from other electronic devices, place
your baby monitor at least 3 feet (1 metre) away from
devices such as wireless routers, microwaves, cell phones
and computers.
1. Place the baby units more than 3 feet (1 metre) away
from your baby.
2. Adjust the angle of the baby unit camera to aim at
your baby.
3. Place the parent unit more than 3 feet (1 metre)
away from the baby units to avoid screeching noise.
Caution
• The default volume of your parent unit is level 3, and the
maximum volume is level 5. If you experience high-pitched
screeching noise from your baby monitor while positioning:
- Make sure your baby units and parent unit are more than
3 feet (1 metre) apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 1000 feet (300 metres) outdoors. The actual
operating range may vary depending on the environmental conditions and other interferences
such as walls, doors and other obstructions.
NOTESNOTE
• The rechargeable battery is pre-installed in your parent unit.
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ tips are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,
or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
Connect the baby monitor
Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged
automatically. The battery icon indicates the battery status (see the following table).
NOTESNOTE
Notes
• The parent unit battery is fully charged after 11 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
• The standby time varies depending on the volume level you set and your actual use.
Battery indicators Battery status Action
The screen displays Battery
low at Parent Unit. The
or light flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about 30 minutes).
The battery icon becomes
solid .
The battery is fully
charged.
To keep the battery charged,
connect it to AC power when not
in use.
User’s manual
VM320
Video Monitor
Congratulations
on purchasing your new VTech product. Before using this product, please read Important safety
instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
Lullaby
The baby monitor has two lullabies and two soothing sounds for you to comfort your baby.
You can play the lullabies or soothing sounds on the baby unit using the parent unit.
1. Press MENU when the parent unit is inactive.
2. Press or to choose , then press or .
3. Press to choose , then press or .
4. Press or to choose a lullaby or a soothing sound, or choose to stop playing.
5. Press SELECT to confirm your selection.
NOTESNOTE
Notes
• The selected lullaby plays for 30 minutes and stops automatically.
• The lullaby playback on the baby unit will be paused when receiving talkback from the parent unit.
1 Connect and charge the battery
What’s in the box
2 Before use
3 Using the baby monitor
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Maximum power used by the transmitter: 0.10W (100mW)
Channels 32
LCD 2.4” Color LCD
(QVGA 320x240 pixel)
Nominal effective range Actual operating range may vary according to environmental
conditions at the time of use.
Power requirements Parent unit: 3.6V Ni-MH battery
Baby unit power adapter: Output: 6V DC @ 400mA
Parent unit power adapter: Output: 6V DC @ 400mA
For pluggable equipment, the socket-outlet (power adaptor) shall be installed near the
equipment and shall be easily accessible.
Technical specifications
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.
All rights reserved. 02/21. VM320_UK_CIB_V4
> 3 ft (1m)
> 3ft (1m)
1
2
> 3ft (1m)
3
>
< 3ft (1m)
3ft (1m)
> 3ft (1m)
< 3ft (1m)
63ē
≥
< 3ft (1m)
3ft (1m)
63ē
63ē
≥
< 3ft (1m)
3ft (1m)
63ē
63ē
＜3ft (1m)
＞3ft (1m)
Screen off timer
You can set the screen off time for the parent unit when there is no key press for a specific time
interval.
When the screen is turned off, you can still hear sound from the baby unit.
1. Press when the parent unit is inactive.
2. Press or to choose , then press or to open the submenu.
3. Press or to choose the desired time period to automatically turn off screen
( / - 5 min./ - 30 min. / - 60min.), then press to confirm your selection.
Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time, or to hear sounds that
exceed a certain level. You can use the parent unit to adjust the microphone sensitivity
of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in
detecting sounds for transmitting to the parent unit. The VOX sensitivity level is preset to
the highest level (Level 5).
VOX
Sensitivity
level Level 5 Level 4 Level 3 Level 2 Level 1
Sensitivity Highest VOX
sensitivity level
High VOX
sensitivity level
Medium VOX
sensitivity level
Low VOX
sensitivity level
Lowest VOX
sensitivity level
Description The parent
unit speaker is
constantly on,
and you will
hear all sounds
(including
background
noises) from
your baby’s
room.
The parent
unit speaker
turns on for
soft babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby sleeps
soundly.
The parent
unit speaker
turns on for
loud babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent unit
speaker turns
on for crying
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent
unit speaker
turns on for
loud crying
or screeching
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
1. Press when the parent unit is inactive.
2. Press or to choose , then press or to open the submenu.
3. Press or to choose the desired sensitivity level, then press to confirm your
selection.
NOTESNOTE
Note
• As long as the Sound-activated screen setting is ON, the screen will turn on automatically when
VOX sensitivity is triggered, despite being off earlier.
Tip
• If you want to use a sound machine or white noise machine for natural white noise while using this baby
monitor to check on your baby, you can:
- Lower the volume of your sound machine or white noise machine; or
- Lower the sensitivity level of your baby monitor to medium (level 3) or below. Default level is the
highest level.
Important
• To maximize the life of the parent unit’s battery, we recommend you fully
charge the battery as instructed, before using the video monitor for the
first time.
Important safety instructions
The applied nameplate is located at the bottom of the baby
unit’s base.
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above
2 metres.
4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not
be used as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water. For example, do not
use it next to a bath tub, wash bowl, kitchen sink, laundry
tub or swimming pool, or in a wet basement or shower.
7. CAUTION: Use only the battery provided. There may be a risk
of explosion if a wrong type of battery is used for the parent
unit. The battery cannot be subjected to high or low extreme
temperature and low air pressure at high altitude during use,
storage or transportation. Disposal of battery into fire or a hot
oven, or mechanically crushing or cutting or the battery can
result in an explosion. Leaving the battery in an extremely
high temperature surrounding environment can result in an
explosion or the leakage of flammable liquid of gas. Battery
subjected to extremely low air pressure may result in an
explosion or the leakage of flammable liquid or gas. Dispose
of used battery according to the instructions.
8. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Power adapter information:
Output: 6V DC 400mA
Ten Pao Industrial Co.,Ltd.
Model: S003ATV0600040(EU),S003ATB0600040(UK);
VTech Telecommunications Limited.
Model: VT05EEU06040(EU), VT05EUK06040(UK).
Rechargeable battery information:
Ni-MH AAA800MAH 3.6V
Model: Corun - Ni-MH AAA800MAH 3.6V
9. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The prongs
are not designed to hold the plug in place if it is plugged
into a ceiling, under-the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Do not cut off the power adapters to replace them with
other plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home,
consult your dealer or local power company.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand
or other unstable surfaces.
17. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product
on a soft surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or heat
register.
18. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any
kind on the product.
19. To reduce the risk of electric shock, do not
disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the
product other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
20. You should test the sound reception every time you turn
on the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using
certain electronic devices, such as baby monitors,
cordless telephones, etc. To protect your privacy, make
sure the product has never been used before purchase,
reset the baby monitor periodically by powering off
and then powering on the units, and power off the
baby monitor if you will not use it for some time.
23. Children should be supervised to ensure that they do not
play with the product.
24. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 0oC
and 40oC.
2. Do not expose the product to extreme cold, heat or
direct sunlight. Do not put the product close to a heating
source.
3. Batteries should not be exposed to excessive heat such as
bright sunshine or fire.
4. Warning—Strangulation Hazard—
Children have STRANGLED in cords. Keep
this cord out of the reach of children (more
than 3 ft (0.9m) away). Do not remove this tag.
5. Never place the baby unit(s) inside the baby’s cot or
playpen. Never cover the baby unit(s) or parent unit with
anything such as a towel or a blanket.
6. Other electronic products may cause interference
with your baby monitor. Try installing your baby
monitor as far away from these electronic devices
as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and cordless
telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the inter-
ference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned
ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the product
is safe to be used based on scientific evidence available
today.
Power on or off the baby unit
• Slide the ON/OFF switch to ON to turn on the baby unit. The POWER LED light turns on.
• Slide the ON/OFF switch to OFF to turn off the baby unit. The POWER LED light turns off.
Power on or off the parent unit
• Slide the ON/OFF switch to ON to turn on the parent unit. The screen and the POWER LED
light turns on.
• Slide the ON/OFF switch to OFF to turn off the parent unit. The screen and the POWER LED
light turns off.
Adjust speaker volume
For parent unit:
• Press VOL /VOL on the parent unit to adjust the speaker volume.
Note
• The parent unit will be muted automatically when the parent unit is talking to the baby unit. When it is
muted, appears on the screen.
For baby unit:
The baby unit speaker volume determines the lullaby volume and talkback volume transmitted
from parent unit. The volume can be adjusted in the parent unit.
1. Press when the parent unit is inactive.
2. Press or to choose , then press or .
3. Press or to choose .
4. Press or to choose the volume level of the baby unit, then press to confirm.
Adjust LCD brightness
You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press when the parent unit is inactive.
2. Press or to choose , then press or .
3. Press or to choose the desired level of brightness, then press to confirm your selection.
Turn on or off the sound activation
When sound activation is on, as long as no sound is detected within 50 seconds, the parent
unit screen will turn off automatically to save power.
When your baby unit detects a sound, which exceeds the selected sensitivity level, the sound
activation triggers the parent unit screen to turn on automatically. When no sound is detected
within 50 seconds, the screen will be off again.
1. Press when the parent unit is inactive.
2. Press or to choose , then press or to open the submenu.
3. Press or to choose or , then press to confirm your selection.
Note
• If the sound sensitivity is set to the highest level, the parent unit screen may remain on continuously
even though sound activation is on. This depends on whether the baby unit detects any sounds.
Zoom
You can zoom in while viewing images from the baby unit.
• Press to zoom in. Press again to zoom out
• Press , , or to move the zoomed image downward, upward, leftward or rightward.
Talk
You can use the TALK function of the parent unit to comfort your baby.
1. Press and hold TALK on the parent unit.
2. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.
3. Release the TALK key to stop the broadcast.
Note
• The parent unit speaker is muted during voice broadcast. Sound transmission from the baby unit
resumes after TALK is released.
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the preset temperature range, the parent unit will
display an alert message.
Set temperature range
You can set the desired minimum and maximum room temperature alert ranges.
1. Press when the parent unit is inactive.
2. Press or to choose , then press .
3. Press or to choose , then press or .
4. Press or to choose or , then press .
5. Press or to choose the desired minimum or maximum temperature, then press to
confirm your selection.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech VM320 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info