To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running
water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the parent unit and the baby unit are dry before you connect them to the mains again.
When you are not going to use the HD video monitor for some time, store the parent unit, the baby
unit and the adaptors in a cool, dry place.
General product care
Storage
To ensure that your HD video monitor is always at its best performance, the Parent Unit
will prompt a message and ask you to update its software and the Baby Unit’s firmware
when there are new versions available. Select “Now” to reboot the system, or switch off
and on the Parent Unit later to reboot the system into the latest software.
• To check if your device is running on the latest software, or to update your device
software, go to:
>Software Update.
Connect your HD video monitor with home Wi-Fi network
• You must connect your video monitor to your secured home Wi-Fi network in order
to receive the latest software and firmware updates. To set the Wi-Fi up, go to:
>Congure Wi-Fi.
Note
• Make sure the Baby Unit is on when you set up the Wi-Fi network.
Auto software and rmware update
Test the sound level and position the HD video monitor
3. To avoid causing feedback noise from your HD video monitor:
• Make sure your baby unit and parent unit are more than 1 metre apart; OR
• Turn down the volume of your parent unit.
4. To avoid interference from other electronic devices, place your baby monitor at least
1 metre away from devices such as wireless routers, microwaves, mobile phones and
computers.
>
1m
<
1m
• This HD video monitor is intended as an aid. It is not a substitute for proper adult supervision, and should
not be used as such.
Testing the sound level of the HD video monitor
• For hearing protection, make sure the parent unit is more than 1 metre away from the baby
unit. If you hear any feedback noise from the parent unit, move the parent unit further until the
noise stops. You can also press- VOL on the parent unit to lower or mute the noise.
• Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the baby unit.
Positioning the HD video monitor
• Keep the baby unit out of the reach of your baby. Never
place or mount the baby unit inside the baby’s cot or
playpen.
1. Place the baby unit more than 1 metre away from
your baby.
2. Adjust the angle of the baby unit to aim at your baby.
Refer to the online help on how to use the Pan/tilt and
Zoom functions of the baby unit.
1m
>
>1m
If you plan to install your baby unit in a designated
location, and use your home Wi-Fi network to
connect your video monitor, you need to test
which of your selected monitoring areas within the
house have good Wi-Fi signal strength. After you
have powered on your parent unit, you can use
your parent unit’s Wi-Fi signal strength indicator
to assist in checking. Once you have identified the
suitable location, you can install your baby unit.
Adjust the distance between your baby unit and
the Wi-Fi router if needed.
• Depending on surroundings and obstructing
factors, such as the effect distance and internal
walls have on signal strength, you may experience
reduced Wi-Fi signal. To improve the Wi-Fi signal
strength, adjust the distance or direction of your
parent unit. Check with your parent unit again.
test the location for the baby unit
mount the baby unit (optional)
1. Place the wall mount bracket on a wall and then use
a pencil to mark the top and the bottom holes as
shown. Remove the wall mount bracket and drill
two holes in the wall (5.5 mm drill bit).
NOTESNOTE
Notes
• Check for reception strength and baby unit’s angle before drilling the holes.
• The types of screws and wall plugs you need depend on the composition of the wall. You may need to purchase the screws and wall plugs separately to mount your baby units.
2. If you drill the holes into a stud, go to step 3.
• If you drill the holes into an object other than a stud, insert the wall
anchors into the holes. Tap gently on the ends with a hammer until the
wall plugs are flush with the wall.
3. Align the wall mount bracket and screws with the
holes in the wall as shown. Tighten the screw in the
middle hole first, so that the wall mount bracket
position is fixed. You can tighten the other screw in
the top hole.
3. Insert the screws into the holes and tighten the screws until only 6.5 mm of
the screws are exposed.
4. Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket
at the bottom to secure the baby unit. Align
the holes on the wall mount bracket with the
screws on the wall, and slide the wall mount
bracket down until it locks into place.
5. You can maximise your baby unit viewing angles by tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in an anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the joint and
secure the angle.
OR
4. Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket at the
bottom to secure the baby unit.
Basic operation
After powering up your video monitor, the parent unit streams live video in local mode.
We recommend you follow the instructions on screen to set up home Wi-Fi network
with your monitor for functionality enhancements and mobile access. See Auto software
and rmware update and Download app for mobile access in this quick start guide.
Use the menu
Press MENU/SELECT to enter the
menu, choose a menu item, or save
a setting. You can use the parent
unit menu for advanced settings or
operations, such as to play or stop the
baby unit lullaby, or adjust the sound
detection setting.
While in the menu:
• Press , , or to scroll among
the menu options.
• Press MENU/SELECT to select an
item.
• Press TALK to return to the live video.
• Press to go to Help & Info page.
Zoom
Press or to zoom in or out.
Adjust speaker volume
Press -VOL / VOL+ to adjust the parent unit
speaker volume level received from the baby
unit.
Talk to your baby via the baby unit
1. Press and hold the TALK key.
2. When the TALK LED turns on,
speak to your parent unit. Your
voice is transmitted to the baby
unit.
3. When finished talking, release
the TALK key.
Turn on/off the screen
Press LCD ON/OFF to turn on or
turn off the parent unit screen
without powering off the parent
unit. You can still hear sound from
the baby unit.
Turn on/off baby unit status LED
You may set the status LED
indicators of your baby unit on or
off. Go to
> Status LED.
Declaration of Conformity
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging,
indicates they must not be disposed of in domestic waste as they contain substances that can be
damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more
than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive
(2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Disposal of batteries and product
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
Please visit www.vtechphones.eu to contact our Customer Service Department.
Customer service and product warranty
This warranty is valid for the UK and Eire only. For products purchased outside
the UK and Eire, please contact your local distributor or place of purchase.
PRODUCT WARRANTY
PRODUCT REGISTRATION
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEARThank you for choosing this quality product from VTech.
We hope it will bring many hours of entertainment,
imaginative play and learning.
1. The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2. The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3. VTech Electronics Europe plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4. If the product covered by this warranty is damaged due to misuse, modification or
unauthorised repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5. This warranty is personal to the original purchaser and is not transferable.
6. Breakages to the LCD screen are not covered by the warranty.
7. Returns to VTech Electronics Europe plc should include a cheque or postal order for
£1.50 towards the cost of return postage and packaging.
8. Products returned to VTech Electronics Europe plc, should be addressed as follows and
packed carefully to avoid damage in transit (Please do not include batteries or adaptor).
Please include details of the fault together with your name and address.
9. To keep an online record of your warranty, please register your product online at www.
vtech.co.uk/warranty
Vtech Electronics EU PLC, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane, West
Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions, find
out about news and events, seek expert advice for parents and
let your kids play fun learning games and activities.
This product is intended for use within Europe and UK.
This equipment complies with the essential requirements to EU’s Radio Equipment Directive
(2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and telecommunication
equipment.
VTech Telecommunications Ltd. hereby declares that this Video Monitor VM901-1W is in compliance
with the essential requirements and other relevant provisions of EU’s Radio Equipment Directive
(2014/53/EU) and UK’s Radio Equipment Regulations 2017.
The Declaration of Conformity for the VM901-1W is available from
www.vtechphones.eu.
Below are the questions most frequently asked about the baby monitor.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby unit and the parent unit.
2. Wait a few seconds before connecting power back to the baby unit and the parent unit.
3. Turn on the baby unit and the parent unit.
4. Wait for the parent unit to synchronise with the baby unit. Allow up to one minute
for this to take place.
Why doesn’t the
baby unit and parent
unit power-on light
illuminate when the units
are switched on?
Perhaps the parent unit is not connected to the power. Insert the adaptor plug into the
parent unit and insert the adaptor in a wall socket. Then, press POWER to switch on the
parent unit to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the adaptor plug into the
baby unit and insert the adaptor in a wall socket. Then, slide the ON/OFF switch to
ON to switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a electronic wall switch.
The battery may de degraded through extended use or defective. See Warranty for
repair/replacement.
Why is my screen in
black and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lighting, objects, colours and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit angle or place the baby unit at a higher level to
prevent glare and a blurry display.
Why does the baby
monitor produce a
feedback noise?
The parent unit and baby unit may be too close to each other.
• Move the parent unit away from the baby unit until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent
unit beep?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but
not less than 1 metre).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit until the battery icon becomes solid .
The temperature of your baby’s room may be too high or too low.
Why don’t I hear a
sound/Why can’t I hear
my baby cry?
The parent unit speaker volume may be too low. Press VOL+ to increase the volume, or
use the parent unit menu to change Sound Sensitivity level to a higher level.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but
not less than 1 metre).
Other electronic products and wireless products may cause interference with your
baby monitor. Try installing your baby monitor as far away from these devices as
possible.
Frequently asked questions
Muted
63ē
10:25 AM
10:25 AM
63ē
10:25 AM
10:25 AM
Press and hold
63ē
10:25 AM
10:25 AM
63ē
> 1 m
<1 m
Manufacturer: VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.
Importer: VTech Electronics Europe Plc
Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
Adult supervision
• This baby monitor should be for use by adults only.
• Do not place the baby unit inside the cot or playpen.
• To ensure your children’s safety, do not allow them to touch or play with the baby monitor and its
accessories. THIS IS NOT A TOY.Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license.
The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.
Android TM and Google Play TM are trademarks of Google Inc.
App Store is a trademark of Apple Inc., registered in the U.S. and other countries.
iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für VTech VM901-1W wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
