809769

VTech VM924 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Dim mode
10 mins inactive
Press any button
The parent unit display will dim to conserve energy after 10 minutes of inactivity, when
no keys are pressed or alerts are received.
Night vision
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal to see a short white glare on
your parent unit screen as the baby unit
adapts to the dark environment.
• When the infrared LEDs are on, the
images are in black and white. This is
normal.
Tip
• Depending on the surroundings and
other interfering factors, like lighting,
objects, colours and backgrounds, the
display resolution may vary. Adjust the
baby unit angle or place the baby unit at a
higher level to prevent glare and a blurry
display.
Mount the baby unit on dry wall (optional)
Place the wall mount bracket on a wall
and then use a pencil to mark two holes in
parallel.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
Drill two holes in the wall (5.5mm inch drill bit ).
If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than
a stud, insert the wall plugs into the holes. Tap
gently on the ends with a hammer until the
wall plugs are flush with the wall.
Align the wall mount bracket and
screws with the holes in the wall as
shown. Tighten the screw in the middle
hole first, so that the wall mount bracket
position is fixed. You can tighten the
other screw in the top hole.
Place the camera unit on the wall mount
bracket, and then slide it forward until
it locks into place. Connect the power
adaptor to the camera unit and a power
supply not controlled by an electronically
controlled wall switch.
NOTESNOTE
Notes
• Check for reception strength and camera
angle before drilling the holes.
• The types of screws and anchors you
need depend on the composition of
the wall. You may need to purchase the
screws and anchors separately to mount
your camera units.
Parent unit icons (Cont’d)
Status icons
Connection status
• - Strong signal strength.
• - Moderate signal strength.
• - Low signal strength.
• - Weak signal strength.
Current view status
• The baby unit is being viewed.
Night vision - On
Zoom - On
Lullaby - On
oF or
oCReal-time temperature
• Real-time temperature
detected by the baby unit in
Fahrenheit (oF) or Celsius (oC)
(e.g. 57
oF or 14
oC).
Status icons
Temperature alert tone - On
Talkback - On
Mute alert
• Displays when the parent unit
speaker volume is set to off.
• Displays when the parent unit is
talking to the baby unit.
Battery status
• animates
when the battery is charging.
• - battery is fully charged.
• - battery is low and needs
charging.
Sound sensitivity and sound activation
Adjust sound detection sensitivity
You can turn on Sound activation and adjust the VOX sensitivity to detect sounds and turn
the parent unit on while the screen is switched off or dimmed.
When the baby unit detects sounds that exceeds the vox sensitivity level setting, the parent
unit screen will turn on and the baby unit starts transmitting the sounds to the parent unit,
and you can see and hear your baby.
If you turn off Sound activation, you will hear sounds from the baby unit all the time, even
when the parent unit screen is switched off.
VOX
Sensitivity
level Level 5
(Highest)
Level 4
(High)
Level 3
(Medium)
Level 2
(Low)
Level 1
(Lowest)
Description (Default setting)
The parent unit
screen and
speaker turn
on for very low
level sounds,
including
background
noises from your
baby’s room.
The parent
unit screen
and speaker
turn on for soft
babbling and
louder sounds
from your baby.
The parent unit
remains quiet
when your
baby sleeps
soundly.
The parent
unit screen
and speaker
turns on for
loud babbling
and louder
sounds from
your baby. The
parent unit
remains quiet
when your
baby makes
soft sounds.
The parent
unit screen
and speaker
turn on
for crying
and louder
sounds from
your baby.
The parent
unit remains
quiet when
your baby
makes soft
sounds.
The parent
unit screen
and speaker
turn on for
loud crying
or screeching
sounds from
your baby.
The parent
unit remains
quiet when
your baby
makes soft
sounds.
Sound activated screen and audio
When Sound activation is on, the parent
unit screen stays off to save power when
the baby unit detects no sound.
Once the baby unit detects sounds
that are louder than the chosen sound
sensitivity level, the parent unit screen
and speaker turn on automatically. The
parent unit will then turn off again after
50 seconds of no sound detection.
NOTESNOTE
Note
• If you have muted the parent unit speaker,
only the parent unit screen will turn on
when sound is detected.
When you are not going to use the HD video monitor for some time, store the parent unit, the baby
unit and the adaptors in a cool and dry place.
Storage
To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a damp cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean under running water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the parent unit and the baby unit are dry before you connect them to the mains again.
General product care
Adult supervision
• This baby monitor should be for use by adults only.
• Do not place the baby unit inside the cot or playpen.
• To ensure your children’s safety, do not allow them to touch or play with the baby monitor and its
accessories. THIS IS NOT A TOY.
Customer service and product warranty
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
Please visit www.vtechphones.eu to contact our Customer Services Department.
Below are the questions most frequently asked about the baby monitor.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby unit and the parent unit.
2. Wait a few seconds before connecting power back to the baby unit and the parent unit.
3. Turn on the baby unit and the parent unit.
4. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute
for this to take place.
why doesn’t the
baby unit and parent
unit power-on light
illuminate when the units
are switched on?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into
the parent unit and insert the adaptor in a wall socket. Then, press and hold POWER to
switch on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the
baby unit and insert the adaptor in a wall socket. Then, slide the ON/OFF switch to
ON to switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a electronic wall switch.
You may have used the battery for a long time. See Warranty for repair/replacement.
Why is my screen in
black and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lightings, objects, colours and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit angle or place the baby unit at a higher level to
prevent glare and a blurry display.
Why does the baby
monitor produce a
feedback noise?
The parent unit and baby unit may be too close to each other.
• Move the parent unit away from the baby unit until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent
unit beep?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but
not less than 1 m).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit until the battery icon becomes solid .
The temperature of your baby’s room may be too high or too low.
Why does the parent
unit react too quickly to
other sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a
sound/Why can’t I hear
my baby cry?
The parent unit speaker volume may be too low. See Adjust parent unit speaker
volume to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the
baby unit to set to a higher level.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but
not less than 1 m).
Other electronic products and wireless products may cause interference with your
baby monitor. Try installing your baby monitor as far away from these devices as
possible.
If you power on only one baby unit, your parent unit may display , and the LINK
LED light will flash.
Frequently asked questions
Disposal of batteries and product
Declaration of Conformity
This product is intended for use within Europe and UK.
This equipment complies with the essential requirements to EU’s Radio Equipment Directive
(2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and telecommunication
equipment.
VTech Telecommunications Ltd. hereby declares that this Video Monitor VM924 is in compliance
with the essential requirements and other relevant provisions of EU’s Radio Equipment Directive
(2014/53/EU) and UK’s Radio Equipment Regulations 2017.
The Declaration of Conformity for the VM924 is available from
http://www.vtech.com/rtte-directive.
Manufacturer: VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.
Importer: VTech Electronics Europe Plc
Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
The crossed-out wheelie bin symbols on products and batteries, or on their respective
packaging, indicates they must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains
more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery
Directive (2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
This warranty is valid for the UK and Ireland only. For products purchased outside
the UK and Ireland, please contact your local distributor or place of purchase.
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR
PRODUCT WARRANTY
Thank you for choosing this quality product from VTech.
1.The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2.The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe Plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3.VTech Electronics Europe Plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4.If the product covered by this warranty is damaged due to misuse, modification or
unauthorized repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5.This warranty is personal to the original purchaser and is not transferable.
6.Breakages to the LCD screen are not covered by the warranty.
7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown
below and packed carefully to avoid damage in transit. Please do not include batteries or
adaptors. Please include details of the fault together with your name and address,
contact phone number and/or email address.
8.To keep an online record of your warranty, please register your product online at
www.vtech.co.uk/clubvtech
VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,
West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech VM924 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info