Bedienungsanleitung Wacom CintiQ - 15X (Seite 18 von 49) (Englisch)

596631

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

■ The maximum resolution of Cintiq is 1024 x 768, True Color (24 bit). As necessary, configure the

display control panel settings for the proper size and color resolution. The number of colors is

constrained by the capabilities of your video card. Refer to the video card manufacturer’s docu-

mentation for details.

For Windows, if you are using Cintiq as a secondary display, you may first need to enable Cintiq

in your Display Properties control panel.

■ After the display portion of Cintiq is working to your satisfaction, move on to the next section (Step

2: Tablet Installation) to install the Wacom tablet portion of Cintiq.

Note: For troubleshooting tips, please refer to page 34.

S T E P 2 : T A B L E T I N S T A L L A T I O N

After you have completed the LCD display installation and configured the display settings, you will

need to connect the Cintiq tablet cabling and install the Wacom tablet driver software.

When installing the tablet portion of Cintiq, refer to the Tablet Cabling Diagram on the following page.

■ First, shut down and power off your computer and Cintiq. If a USB port is available, Wacom

recommends installing Cintiq as a USB device.

■ For USB installation: Choose the Cintiq USB cable

Plug the round end into the Cintiq port labeled USB. Plug the other end into an available USB port

on your computer. See E in the connection diagram on page 17.

Important: Make sure you select the correct cable and that you plug it into the correct port.

■ For Serial installation: Choose the Cintiq serial cable

Plug the round end into the Cintiq port labeled . Plug the other end into an available serial

port on your computer. See F in the connection diagram on page 17. For UNIX workstations,

you may need to use an appropriate adaptor from the Wacom UNIX kit to connect the serial cable.

Important: Make sure you select the correct cable and that you plug it into the correct port. If the

connection is difficult to make, do not force the plug into the connector. Instead, verify that there

are no bent pins and that you have the correct cable and location. Do not plug in or unplug the

serial connector when your computer is running—this may damage your serial card.

■ At the back of Cintiq, insert all three cables between the cable guides and then slide the connector

panel cover into place over the cable connectors. Do not skip this step, as the panel cover will

reduce the possibility of accidentally disconnecting the cables.

■ Next, depending on your operating system and the tablet interface that you will be using (USB or

serial), refer to the appropriate section for software installation instructions:

Tablet Software Install for Macintosh See page 18

Tablet Software Install for Windows with USB Connection See page 19

Tablet Software Install for Windows with Serial Connection See page 20

Tablet Software Install for SGI or Sun See page 21

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wacom CintiQ - 15X Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info