Bedienungsanleitung Wacom Graphire bluetooth (Seite 14 von 71) (Englisch)

444762

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

WORKING WITH GRAPHIRE

INDEX

CONTENTS

INDEX

CONTENTS

3. While the tablet is in discoverable mode, pair it to your computer. The following points provide a general

overview of the pairing process. For detailed instructions on pairing a Bluetooth device to your

computer, refer to the documentation that came with your operating system or Bluetooth support.

• Open the Bluetooth devices control panel. Some common access points to this control panel

include: the task bar, menu bar, control panel, or system preferences pane of your computer’s

operating system.

• From the Bluetooth devices control panel, start the process of adding a device. Common options to

do so are A

DD A BLUETOOTH DEVICE, BLUETOOTH SETUP, or SET UP NEW DEVICES.

• In the setup assistant that appears, carefully follow all directions to continue.

• If prompted for the device type to set up, choose “mouse”.

• When the tablet is discovered it will show up as WACOM PEN TABLET. Select it and continue to

follow the prompts. If the tablet does not appear, you will need to refresh the assistant and again

press the tablet C

ONNECT button.

• If prompted for an authentication code or passkey, select the “don’t use” or “no” option. The Graphire

Bluetooth pen tablet does not require passkey authentication.

• If prompted for the device type services to add, choose the option for “tablet”. Otherwise choose

“mouse”.

• After the wireless tablet has been successfully paired to your computer it will appear as a connected

device in the Bluetooth devices control panel.

4. Close the Bluetooth devices control panel and check the connection. Place the pen on the tablet – you

should be able to move the screen cursor with the pen.

Once you have established a connection between your wireless tablet and the computer, they will

remember the connection – just as if you had connected a virtual cable between them. The tablet will

remember which computer it is connected to, and will reject all attempts by other computers to connect

to it.

• If the link is broken for more than two seconds (e.g., you shut down your computer, unplug your

USB-to-Bluetooth adapter or otherwise switch off your Bluetooth support, or move the tablet too far

away from the computer), the tablet will switch itself off.

• When starting up your computer, wait until your operating system has completely loaded and then

push the tablet power button. The Bluetooth connection will automatically be reestablished.

• If you again press the C

ONNECT button, the virtual cable link will be broken and the tablet will once

again become discoverable by any Bluetooth enabled computer.

Important: Remember that the Graphire Bluetooth pen tablet driver software must be installed

before you will be able to work with full tablet functionality and features such as pressure-sensitivity

with the pen.

5. If you have not already done so, install the pen tablet driver software. Insert the Wacom Pen Tablet

Driver CD into your computer’s CD-ROM drive, click on the I

NSTALL TABLET link, and follow the prompts

to install the driver software.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wacom Graphire bluetooth Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wacom Graphire bluetooth

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info