Bedienungsanleitung Wacom Intuos3 (Seite 73 von 92) (Englisch)

444763

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

APPENDIX

INDEX

CONTENTS

INDEX

CONTENTS

Conﬁguring tablet menus and screen pointing areas in AutoCAD

A screen pointing area is a rectangular region on the tablet surface where the tablet acts like a system

mouse. When the pointer is within a screen pointing area, the tablet can access windows, menus, and other

applications outside AutoCAD’s drawing area. You can conﬁgure both a ﬁxed and ﬂoating screen pointing

area.

Before you conﬁgure the tablet, its entire surface is the ﬁxed screen pointing area. AutoCAD recommends

that you change the size of the ﬁxed screen pointing area so that a small screen area on your tablet maps to

the entire monitor screen. AutoCAD also recommends that you select the default tablet menus, columns,

and rows they provide.

After you conﬁgure the tablet menus, AutoCAD prompts you for the ﬁxed and ﬂoating screen pointing areas.

This allows you to designate a tablet area as a Windows system pointer.

The ﬁxed screen pointing area is disabled when you digitize points into AutoCAD with T

ABLET MODE ON.

This is due to the ﬁxed correspondence between the tablet and AutoCAD’s drawing area. To access menus

from the tablet, you must use the ﬂoating screen pointing area. This allows you to access a menu from

anywhere on the tablet surface, and to toggle it off when ﬁnished. You can deﬁne a tool button to toggle the

ﬂoating screen area on and off.

Important. The ﬂoating screen pointing area takes precedence over menu areas, Tablet Mode On,

and the ﬁxed screen pointing area.

1. From the D

RAWING EDITOR, open the TOOLS menu (OPTIONS menu for Release 13).

2. Select TABLET, and then CONFIGURE.

3. Deﬁne tablet menu areas. Follow the prompts at the bottom of the AutoCAD Drawing Editor. Type the

number of tablet menu areas you want (0-4) and press E

NTER. If you do not want to use a menu

template, type 0 (zero). Digitize the upper-left, lower-left, and lower-right corners of the menu area and

then press E

NTER. Next, enter the number of columns and press ENTER. Now enter the number of rows

and press E

NTER. Repeat for each menu area.

4. Deﬁne the ﬁxed screen pointing area. By default, the entire tablet is a ﬁxed screen pointing area. If you

are using a menu template, you should re-specify the ﬁxed screen pointing area to match the template.

Continue to follow the prompts at the bottom of the A

UTOCAD DRAWING EDITOR screen.

5. Deﬁne the ﬂoating screen pointing area – it allows you to access all areas of the screen. The ﬂoating

screen pointing area takes precedence over T

ABLET MODE ON, the ﬁxed screen pointing area, and the

menu areas. Continue to follow the prompts at the bottom of the A

UTOCAD DRAWING EDITOR screen.

Please check your AutoCAD documentation for additional information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wacom Intuos3 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wacom Intuos3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info