Bedienungsanleitung Wacom intuos4 (Seite 78 von 101) (Englisch)

444750

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

Index

Contents

IndexContents

CONFIGURING TABLET MENUS AND SCREEN POINTING AREAS IN AUTOCAD

A screen pointing area is a rectangular region on the tablet surface where the tablet acts like a system

mouse. When the pointer is within a screen pointing area, the tablet can access windows, menus, and other

applications outside AutoCAD’s drawing area. You can configure both a fixed and floating screen pointing

area.

Before you configure the tablet, its entire surface is the fixed screen pointing area. AutoCAD recommends

changing the size of the fixed screen pointing area so that a small screen area on your tablet maps to the

entire monitor screen. AutoCAD also recommends selecting the default tablet menus, columns, and rows

they provide.

After you configure the tablet menus, AutoCAD prompts you for the fixed and floating screen pointing areas.

This allows you to designate a tablet area as a Windows system pointer.

The fixed screen pointing area is disabled when you digitize points into AutoCAD with T

ABLET MODE ON.

This is due to the fixed correspondence between the tablet and AutoCAD’s drawing area. To access menus

from the tablet, you must use the floating screen pointing area. This allows you to access a menu from

anywhere on the tablet surface, and to toggle it off when finished. You can define a tool button to toggle the

floating screen area on and off.

Important: The floating screen pointing area takes precedence over menu areas, T

ABLET MODE ON,

and the fixed screen pointing area.

1. From the D

RAWING EDITOR, open the TOOLS menu (OPTIONS menu for Release 13).

2. Select T

ABLET, and then CONFIGURE.

3. Define tablet menu areas. Follow the prompts at the bottom of the AutoCAD Drawing Editor. Type the

number of tablet menu areas you want (0-4) and press E

NTER. If you do not want to use a menu

template, type 0 (zero). Digitize the upper-left, lower-left, and lower-right corners of the menu area and

then press E

NTER. Next, enter the number of columns and press ENTER. Now enter the number of rows

and press E

NTER. Repeat for each menu area.

4. Define the fixed screen pointing area. By default, the entire tablet is a fixed screen pointing area. If you

are using a menu template, you should re-specify the fixed screen pointing area to match the template.

Continue to follow the prompts at the bottom of the A

UTOCAD DRAWING EDITOR screen.

5. Define the floating screen pointing area – it allows you to access all areas of the screen. The floating

screen pointing area takes precedence over T

ABLET MODE ON, the fixed screen pointing area, and the

menu areas. Continue to follow the prompts at the bottom of the A

UTOCAD DRAWING EDITOR screen.

Please check your AutoCAD documentation for additional information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wacom intuos4 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wacom intuos4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info