Bedienungsanleitung Wagner Super Finish 31 (Seite 11 von 30) (Deutsch, Englisch, Französisch, Italienisch)

649002

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Super Finish 27 • 31

Cleaning unit from outside

Achtung



spray gun is alternately opened and closed.

Achtung

In case of coating materials diluted with









Fill upper hopper with suitable cleaning agent.1.

Switch on unit, set multifunction switch to

(ON -

circulation).

Operate unit for a few minutes in circuit with spray gun

closed (without tip).

Set multifunction switch to 4. (spray).

Pull trigger guard on spray gun.5.

Pump cleaning agent into a separate, open container until 6.

the unit is empty.

Attention

In the case of coating materials containing sol-

vents, the container must be earthed.

Danger





See safety regulations.

Switch o unit, set multifunction switch to 7.

(OFF).



Danger

First of all pull out mains plug from socket.



Leave the suction system submerged in the coating

material or submerge it into the appropriate cleaning agent.

Suction lter and unit should not dry out.

Attention

In using quick-drying - or two-component

coating material, do not fail to rinse unit

through with a suitable cleaning agent during

the processing period.

8. 



Cleanliness is the surest guarantee for disturbance-free opera-

tion. Always clean the unit after completing spraying work. In

no event may residue of the coating material dry and collect

in the unit. The cleaning agent used for cleaning (only with

a ash point of over 21 °C) must correspond to the coating

material.





see operating manual for spray gun.

Dismount tip and clean, see page 45, point 13.2.





Remove suction system from the material vessel, e.g. put

unit in the horizontal set-up position.

Switch on unit, set multifunction switch to

(ON–

circulation) and further to (spray).

Pull the trigger guard on the spray gun in order to pump

residue coating material from the suction pipe, the high-

pressure hose and the spray gun into an open container.

Attention

In case of coating material containing solvents,

the vessel must be earthed.

Danger





regulations.

Submerge suction system in a suitable cleaning agent.4.

Set multifunction switch to 5.

(OFF).

Screw on spray gun on suction pipe (g. 12) with the two 6.

accompanying spanners 22 mm.

Set multifunction switch to 7. (ON – circulation).

Pump suitable cleaning agent in the circuit for approx.

1 minute.

Pull trigger guard on spray gun and hold with clamp.9.

Set multifunction switch to 10. (spray).

Clean suction pipe for about three minutes.11.

Rinse in circuit – set multifunction switch to 12. (ON).

Close spray gun.13.

When cleaning with water, repeat procedure for about three

14.

minutes with clear water.

Switch o unit – set multifunction switch to 15. (OFF).

Cleaning unit (shutting down operation)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wagner Super Finish 31 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info