Bedienungsanleitung Wahl Tondeuse diverse types (Seite 1 von 2) (Englisch)

484284

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Middle

are aligned properly. (See Clipper Maintenance Instructions.)

10. During use, do not place or leave appliance where it may be damaged by an

animal or exposed to weather.

11. To disconnect, turn all controls to “OFF,” then remove plug from outlet.

12.

Turn all controls to “OFF” before attaching or detaching detail trimmer blades.

SAVE THESE INSTRUCTIONS

This Clipper Has Been Designed For Household Use Only

OIL

The blades of your new clipper should be oiled every

few haircuts. Place a few drops of Wahl Clipper Oil

on the teeth of the blades as well as at the back of

the blade . Use only the Wahl Clipper Oil included in

the pack. Do not use hair oil, grease or any oil mixed

with kerosene or any solvent.

POWER SCREW

Your clipper has a power screw and it has been

adjusted for peak efficiency before leaving the factory.

However, if voltage in your home is low, you may need to

readjust it. To adjust power, turn your clipper

“ON”

. Use the

end of the cleaning brush or a screwdriver to turn power

screw in a clockwise direction until you hear a noise. Then,

slowly turn power screw in a counterclockwise direction, just

until noise stops. This is the maximum power setting.

CORD

The cord should not be used to pull the clipper. Since freedom

of movement needs to be

maintained, care should be used to keep the cord untwisted and unobstructed.

If your clipper has a polarized plug: To reduce the risk of electric shock, this appliance

has a polarized plug (one blade is wider than the other). This plug fits in a polarized outlet only

one way. In the event the plug does not fit fully in the outlet, reverse the

plug. Do not change the plug in any way.

TAPER LEVER

The taper lever adds versatility to your clipper by allowing you to

gradually change the closeness of your cut. (Up position = closest

cut; Down position = longest cut) Should the blades become

jammed with hair, move the taper lever up and down several times.

This will help free up the blades.

LIMITED WARRANTY

(Valid in U.S.A. only)

If your Wahl product fails to operate satisfactorily within five (5) years from the date of original

purchase or receipt as a gift, Wahl will, at our option, repair or replace it and return it to you FREE

OF CHARGE.

DO NOT RETURN THIS PRODUCT TO STORE WHERE PURCHASED. PRODUCTS NEEDING REPAIR

UNDER THIS WARRANTY SHOULD BE RETURNED WITH POSTAGE PREPAID TO:

WAHL CLIPPER CORPORATION

ATTN: REPAIR DEPARTMENT

3001 LOCUST STREET

STERLING, ILLINOIS 61081

Include a note describing the defect and the date of original purchase or receipt as a gift (if in

warranty). Products out of warranty will be repaired at our standard repair charges.

This warranty is void and no repair or replacement will be made under this warranty or otherwise if:

1. The product is modified in any manner.

2. The product is repaired by anyone other than Wahl Clipper Corporation.

3. The product has been subject to unreasonable use.

This warranty gives you specific legal rights and you may also have other rights which may

vary

from state to state. No other written express warranty is given. Any implied warranty, including any

warranty of merchantability which may arise from purchase or use, is limited to the five-year period

provided in this express warranty. Some states may not allow such limitation, so it may not apply to

you. No responsibility is assumed for incidental or consequential damages of any type, or for the use

of unauthorized attachments. Some states may not allow the exclusion or limitation of incidental or

consequential damages, so the limitation or exclusion may not apply to you. Warranty valid in U.S.A.

only. Outside U.S.A., check with store for Wahl authorized distributor’s warranty.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed,

including the points listed below. Read all instructions and safeguards before using.

DANGER —

To reduce the risk of injury or death by electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.

Some electrical parts inside the clipper are electrically live, even with the switch

“OFF.”

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be pulled into a tub or sink.

Do not place in or drop into water or other liquid.

4. Always unplug this appliance from the electrical outlet immediately after using.

5. Unplug this appliance before cleaning.

WARNING —

To reduce the risk of burns, fire, electric shock or injury to persons:

1. An appliance should never be left unattended when plugged in.

2. Close supervision is necessary when this appliance is used by, on, or near

children or invalids.

3. Use this appliance only for its intended use, as described in this manual. Do

not use attachments not recommended by the manufacturer.

4. Never operate this appliance if it has a damaged cord or plug, if it is not

working properly, if it has been dropped or damaged, or dropped into water.

Return the appliance to Wahl Clipper Corporation for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never operate the appliance with the air openings blocked or while on a soft

combustible surface, such as a bed or couch, where air openings may be

blocked. Keep the air openings (if any) free from lint, hair or the like.

7. Never drop or insert any object into any opening on this appliance.

8. Do not use outdoors or operate with aerosol (spray) products or where oxygen

is being administered.

9. Do not use this appliance with a damaged or broken comb nor with teeth

missing from the blades, as injury may occur. Before use, make certain blades

Please register your Wahl Clipper online at: www.wahlhaircuts.com

Purchase Confirmation-

With the information your provide, we confirm the date of purchase of your product. This

confirmation is of benefit to you, especially if your original proof of purchase is lost.

Proof of Ownership-

Your UPC number, item number and other information will be kept in our files for up to ten years.

For personal attention from one of our customer service representitives please contact us at:

www.wahlhaircuts.com or 1-800-767-9245

P.O. Box 578, Sterling, Illinois 61081 USA

Part #94601-303

CLIPPER MAINTENANCE

Taper Lever

(Multi-Cut [MC] Clipper Only)

Top Blade

Bottom

Blade

Switch

Power Screw

ALIgNINg CLIPPER bLADES

Your Wahl clipper blades were oiled and aligned before leaving our factory. Blades may need

to be realigned if they have been bumped or removed for cleaning. To determine if realignment

is necessary, compare your clipper blades with this sketch.

1. If your clipper has a taper lever, position the lever in the close cut position.

2. End of top blade teeth should be approximately 1/32-inch (.64 mm) back from bottom blade.

3. Extreme left-hand tooth of top blade must be covering or to the left of the first small tooth

of bottom blade.

4. Extreme right-hand tooth of top blade must be touching the big tooth on the bottom blade.

If blade alignment is incorrect, add a few drops of Wahl Clipper Oil to the blades, turn clipper

“ON” for a few moments, turn “OFF” and unplug. Loosen screws slightly and adjust. Tighten

screws after blades are aligned. Other than blades, this clipper has no user-serviceable parts.

1. Comb hair and

remove tangles. Attach

the largest guide comb

to the clipper. Make sure

the taper lever is in the

up position.

2. Start at hairline on

side of head and cut

up to middle of head.

Note: If cut hair is

too long repeat with

next smaller guide

comb.

3. Continue around

head repeating step 2.

4. You are now ready to

cut the middle portion of

the hair.

5. Select the proper guide

comb. Use the comb with

the next highest number

than in step 3. Example:

If you used a #6 comb in

step 3, select comb #7.

6. Continue cutting

around middle portion of

head as in steps 2 and 3.

7. For cutting top of

head, use the comb with

the next highest number

than in step 6.

Start at front bang area.

8. Cut across top of

head.

9. Comb hair on entire

head to assess if further

cutting is necessary.

10. Blend out any cut

lines. Lines may form

where you change comb

sizes. Use the same

comb used in step 3

with taper lever in down

position.

12. Using the comb used in

step 8 repeat blending the

top outline as in step 10.

O U T L I N I N G

T A P E R I N G

1. The ear guide combs

have a built in taper

ranging from 1/8” to 1/2”.

2. Attach the left ear

guide comb to the

clipper. Put taper lever in

down position.

3. Hold the clipper at a

slight angle just back of

the ear at the hairline.

Hold top of ear down.

4. Move the clipper

upward and around

the ear.

Repeat the same for the

right ear with the right

ear guide comb.

1. Select the guide comb

for the desired length

hair. Attach to clipper

with the taper lever in

the up position.

2. Hold the clipper flat

against the neck and

slowly move the clipper

through the hair as

shown.

3. Use the same procedure

from the lower side of the

head to the upper side of

the head.

C R E W C U T S

B L E N D I N G

For more information or product

registration, visit wahlhaircuts.com

1. Attach the brow trim guide to clipper

2. Starting from just above your nose, slowly guide

the clipper to the outside of your face.

For shorter brow trim repeat steps 1 and 2

working from outside face to your nose.

1. Attach ear trim guide to clipper.

2. Hold the clipper at a 45-degree angle.

3. Slowly move the clipper from back to front.

Avoid poking eyes.

B R O W T R I m G U I D E E A R T R I m G U I D E

1. No attachments

needed. Push the taper

lever up to the close cut

position.

2. Start with the

sideburns.

3. Continue around ear

as shown.

ATTACHING GUIDE COMBS

Align comb onto blade then press

tab until you hear a snap.

C U T T I N G H A I R

11. Using a rocking

motion, blend out the

middle cut line.

4. Cut the top using a

guide comb two sizes

(lengths) longer than the

comb used on sides. Start

at the front and cut slowly

to the back as shown.

4. Trim neckline as

shown.

5. Around the ears.

guIDE COMb LISTINg

Some kits do not include all Wahl guide combs. Some kits include colored

guide combs for ease in remembering which combs were previously used.

(1.5mm)

/16”

Light Green/Black

(3mm)

/8”

Red/Black

(4.5mm)

/16”

Burgundy/Black

(6mm)

/4”

Purple/Black

(10mm)

/8”

Dark Blue/Black

(13mm)

/2”

Orange/Black

(16mm)

/8”

Yellow/Black

(19mm)

/4”

Lavender/Black

(22mm)

/8”

Green/Black

(25mm) 1”

Light Blue/Black

(38mm) 1

”

Black Only

(31mm) 1

”

White Only

NOTE:

1) Always start with the largest guide

comb, then use shorter combs if a

shorter length is desired.

2) Cut only a small amount until you

become accustomed to how long

each guide comb leaves the hair.

3) Cut slowly and smoothly. Do not

force the clipper through the hair.

Home

Haircutting

witH

ActuAl BlAde Size

NOTE:

NOT ALL WAHL KITS

INCLUDE BROW OR

EAR TRIM GUIDE

The first time you cut hair, cut only

a small amount of hair until you

become accustomed to the length

of hair each guide comb provides.

• Start by attaching the largest

guide comb on the clipper.

• Then use shorter combs if a

shorter length is desired.

• For uniform cutting, cut at a

slow even speed.

TImE

CUTTING HAIR

Wahl Tondeuse diverse types Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wahl Tondeuse diverse types

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info