Middle
are aligned properly
10.
animal or exposed to weather
11.
12.
SA
This Clipper Has Been Designed For Household Use Only
OIL
The blades of your new clipper should be oiled every
few haircuts. Place a few drops of Wahl Clipper Oil
on the teeth of the blades as well as at the back of the
blade . Use only the Wahl Clipper Oil included in the
pack. Do not use hair oil, grease or any oil mixed with
kerosene or any solvent.
PO
Y
adjusted for peak efficiency before leaving the factory
However
readjust it. T
“ON ”
. Use the
end of the cleaning brush or a screwdriver to turn power
screw in a clockwise direction until you hear a noise. Then,
slowly turn power screw in a counterclockwise direction, just
until noise stops. This is the maximum power setting.
CORD
The cord should not be used to pull the clipper
of movement needs to be
maintained, care should be used to keep the cord untwisted and unobstructed.
If your clipper has a polarized plug: T
has a polarized plug (one blade is wider than the other). This plug fits in a polarized outlet only
one way
plug. Do not change the plug in any way
T
The taper lever adds versatility to your clipper by allowing you to
gradually change the closeness of your cut. (Up position = closest
cut; Down position = longest cut) Should the blades become
jammed with hair
This will help free up the blades.
LIMITED W
(Valid in U.S.A. only)
If your Wahl product fails to operate satisfactorily within five (5) years from the date of original
purchase or receipt as a gift, Wahl will, at our option, repair or replace it and return it to you FREE
OF CHARGE.
DO NOT RETURN THIS PRODUCT TO STORE WHERE PURCHASED. PRODUCTS NEEDING REP
UNDER THIS WARRANTY SHOULD BE RETURNED WITH POST
WAHL CLIPPER CORPORA
A
3001 LOCUST STREET
STERLING, ILLINOIS 61081
Include a note describing the defect and the date of original purchase or receipt as a gift (if in
warranty). Products out of warranty will be repaired at our standard repair charges.
This warranty is void and no repair or replacement will be made under this warranty or otherwise if:
1. The product is modified in any manner
2. The product is repaired by anyone other than Wahl Clipper Corporation.
3. The product has been subject to unreasonable use.
This warranty gives you specific legal rights and you may also have other rights which may
vary
from state to state. No other written express warranty is given. Any implied warranty
warranty of merchantability which may arise from purchase or use, is limited to the five-year period
provided in this express warranty
you. No responsibility is assumed for incidental or consequential damages of any type, or for the use
of unauthorized attachments. Some states may not allow the exclusion or limitation of incidental or
consequential damages, so the limitation or exclusion may not apply to you. Warranty valid in U.S.A.
only
IMPOR
When using an electrical appliance, basic precautions should always be followed,
including the points listed below
DANGER —
T
1.
Some electrical parts inside the clipper are electrically live, even with the switch
“OFF
2.
3.
Do not place in or drop into water or other liquid.
4.
5.
W
T
1.
2.
children or invalids.
3.
not use attachments not recommended by the manufacturer
4.
working properly
Return the appliance to Wahl Clipper Corporation for examination and repair
5.
6.
combustible surface, such as a bed or couch, where air openings may be
blocked. Keep the air openings (if any) free from lint, hair or the like.
7.
8.
is being administered.
9.
missing from the blades, as injury may occur
Please register your Wahl Clipper online at: www
Purchase Confirmation-
With the information you provide, we confirm the date of purchase of your product. This
confirmation is of benefit to you, especially if your original proof of purchase is lost.
Proof of Ownership-
Y
For personal attention from one of our customer service representitives please contact us at:
www.wahlhair
© 2011 WAHL CLIPPER CORPORA
P
Part #94601-2201
CLIPPER MAINTENANCE
T
(Multi-Cut [MC] Clipper Only)
T
Bottom
Blade
Switch
Power Screw
ALIGNING CLIPPER BLADES
Y
to be realigned if they have been bumped or removed for cleaning. T
is necessary
1.
2.
3.
of bottom blade.
4.
If blade alignment is incorrect, add a few drops of Wahl Clipper Oil to the blades, turn clipper
“ON” for a few moments, turn “OFF” and unplug. Loosen screws slightly and adjust. Tighten
screws after blades are aligned. Other than blades, this clipper has no user
1. Comb hair and
remove tangles. Attach
the largest guide comb
to the clipper
the taper lever is in the
up position.
2. Start at hairline on
side of head and cut
up to middle of head.
Note: If cut hair is too
long repeat with next
smaller guide comb.
3. Continue around
head repeating step 2.
4. Y
cut the middle portion of
the hair
5. Select the proper guide
comb. Use the comb with
the next highest number
than in step 3. Example:
If you used a #6 comb in
step 3, select comb #7.
6. Continue cutting
around middle portion of
head as in steps 2 and 3.
7. For cutting top of
head, use the comb with
the next highest number
than in step 6 .
Start at front bang area.
8. Cut across top of
head.
9. Comb hair on entire
head to assess if further
cutting is necessary
10. Blend out any cut
lines. Lines may form
where you change comb
sizes. Use the same comb
used in step 3 with taper
lever in down position.
12. Using the comb used in
step 8 repeat blending the
top outline as in step 10.
OUTLINING
T
1. The ear guide combs
have a built in taper
ranging from 1/8” to 1/2”.
2. Attach the left ear
guide comb to the
clipper
down position.
3. Hold the clipper at a
slight angle just back of
the ear at the hairline.
Hold top of ear down.
4. Move the clipper
upward and around
the ear
Repeat the same for the
right ear with the right
ear guide comb.
1. Select the guide comb
for the desired length
hair
with the taper lever in
the up position.
2. Hold the clipper flat
against the neck and
slowly move the clipper
through the hair as
shown.
3. Use the same procedure
from the lower side of the
head to the upper side of
the head.
CREW CUTS
BLENDING
1. No attachments
needed. Push the taper
lever up to the close cut
position.
2. Start with the
sideburns.
3. Continue around ear
as shown.
A
Align comb onto blade then press
tab until you hear a snap.
CUTTING HAIR
11. Using a rocking
motion, blend out the
middle cut line.
4. Cut the top using a
guide comb two sizes
(lengths) longer than the
comb used on sides. Start
at the front and cut slowly
to the back as shown.
4. T
shown.
5. Around the ears.
GUIDE COMB LISTING
Some kits do not include all Wahl guide combs. Some kits include colored
guide combs for ease in remembering which combs were previously used.
#
1
-
(3mm )
1
/8”
Black
#
2
-
(6mm )
1
/4”
Black
#
3
-
(10mm )
3
/8”
Black
#
4
-
(13mm )
1
/2”
Black
#
5
-
(16mm )
5
/8”
Black
#
6
-
(19mm )
3
/4”
Black
#
7
-
(22mm )
7
/8”
Black
#
8
-
(25mm ) 1
Black
Left
Black
Right
Black
NOTE:
1) Always start with the largest guide
comb, then use shorter combs if a
shorter length is desired.
2) Cut only a small amount until you
become accustomed to how long
each guide comb leaves the hair
3) Cut slowly and smoothly
force the clipper through the hair
Home
Haircutting
witH
ActuAl lAde ize
The first time you cut hair
of hair until you become accustomed to the length
of hair each guide comb provides.
• Start guide comb on
the clipper
• Then
desired.
• For
1
ST
TIME
CUTTING HAIR
PRODUCT
REGISTRA
For more information or product
registration, visit wahlhaircuts.com
