Bedienungsanleitung Wamsler K158 (Seite 44 von 120) (Deutsch, Englisch, Französisch, Italienisch)

813271

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

2. ARRANGEMENT

For installation and for connection of flue, the requirements of the Fire Regulations (FeuVO

in Germany) apply, as well as local building regulations such as the following technical

standards DIN 4705, EN 13384, DIN 18160, EN 1856-2, EN 12828, EN 12831, EN 12897

and EN 15287. In order for the stove to function correctly the chimney to which you want to

connect the stove must be in good condition.

NOTE

The room must reach the so-called room capacity ratio of 4 m3 per kW nominal heat

capacity. If this is not possible, then it has to be connected to other rooms on an air

flow sense, i.e. with rooms with outside doors or windows and air vents in the con-

necting doors or walls to the installation room.

2.1 Fire safety

All flue pipes must be capable of withstanding up to +400 °C.

If the stove is to be installed on a floor of combustible material such as wood or plastic etc.,

then a floor plate must be installed which is larger than the footprint of the stove from the

fire door to each side by at least 30 cm and to the front of the fire door by at least 50 cm.

The walls to the sides and back of the stove cannot be of combustible material nor can

they be clad in combustible material, where the distance is less than 20 cm from the stove.

The bottom edge of wall cupboards above the stove must be at least 70 cm above the

hotplate surface. The side distance from wooden or plastic furniture parts must also be

more than 20 cm. These safety distances can be reduced to 10 cm if the special distance

connections are also supplied.

Care should be taken that the smoke pipe is at least 40 cm from combustible building

materials such as wooden or plastic cladding or door frames or wallpaper. This distance

can be reduced by half, if the smoke pipe is insulated so that any part of the building is

prevented from being heated to above +80 °C.

In addition local building regulations have also to be complied with.

2.2 Chimney attachment

The connecting pipe between the stove and the chimney should have the same cross

section as the pipe connection on the stove. The chimney cross section should be consis-

tent and as far as possible square or round. House chimneys should be insulated.

This applies particularly to the smoke pipe and sheet metal chimneys. They should be

provided with good heat insulation at points where there is the possibility of being exposed

to cooling. Modern chimneys from prefabricated parts or multilayer construction are pre-

ferred, in as far as they are approved by the local building authority. Horizontal smoke pipe

runs of over 0.5 m long must rise by ten degrees to the connection with the flue. Pipes

which are not heat protected or are not vertical, should not longer than 1.25 m.

The effective flue height from the middle of the pipe connection to the top of the chimney

must be at least 5 m.

Should the height be less than the stove must be connected to a vertical flue pipe which is

not less than 1 m in length.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wamsler K158 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info