Bedienungsanleitung Wanders Boreal (Seite 23 von 60) (Deutsch, Englisch, Holländisch, Französisch)

533428

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

must be clean, leak-proof and without obstructions,

and must have a diameter of 150 mm.

• Any bends in the ue tube must not exceed 45

degrees.

• Ensurethatthechimneytubecandischargetheue

gases adequately, properly and safely.

Supply of combustion air

The stove must have a sufﬁcient fresh supply of

combustion air. To avoid draft, make if necessary an

extra air supply opening as close to the stove as possible.

An extra air supply opening is deﬁnitely required if:

• theroomhasaheatrecoverysystem.

• theroomhasacentralexhaustsystem.

• thesamespacehasacookerhood.

The air supply opening must be sealable if it goes through

a ﬁre-resistant wall. If there are several heating devices

in the same room there must be enough air openings to

guarantee proper combustion.

With the Boreal you can also opt for an external air

supply connection to the bottom of the stove. The length

andthediameteroftheairsupplyductareimportant;the

maximum length of a 100 mm diameter air supply duct

is 1 meter and the duct can have one bend of 90°. If the

duct exceeds 1 meter you must increase its diameter.

Fire Safety

For reasons of ﬁre safety is it important to observe the

instructions below before installing the stove.

1. The free distance from the ﬁre-proof rear wall is at

least 10 cm in each rotated position.

2. Keep at least a distance of 80 cm between the stove

and combustible objects such as curtains, wooden

objects (cupboards and paintings) and glass objects.

Keep the same distance from the ﬂue tube.

3. Wooden construction parts within the radiation

range of the stove (80 cm from the exterior of the

stove) must be covered with ﬁreproof material.

4. If the ﬂue tube goes through a ceiling and/or roof

that consist of ﬂammable materials, the ceiling and

the roof must be covered with ﬁreproof materials all

around (about 80 cm). Pay also attention to joisted

ﬂoor layers and any electric wiring.

5. Keep a distance of at least 50 cm (in all directions)

between the stove and supporting steel construc-

tion parts.

6. Shield off all combustible materials within a radius

of 80 cm from the stove openings with non-com-

bustible materials.

7. The wall behind the stove must consist of, or be

insulated with, ﬁre-proof materials. The insulation

material must resist a temperature of 700 °C and

have a density of 80 kg/m3. Please see for insulation

materials table on page 26).

8. Avoid heat transmission when placing the stove.

Heat transmission of a burning stove can penetrate

the wall and even cause ﬁre damage on the other

side of the wall. Prevention is better than cure.

Installation

The Boreal is tested in accordance with the international

EN 13240 standardization, and has an extra additional

standardization for optimally environment-friendly

heating devices related to ﬂue gases (Section 15a B-Vg.

Des BmfWA). The stove can be connected to a ﬂue tube

to which several stoves are connected. The Boreal must

never be inserted into a wall.

The heating device must be placed and connected by an

acknowledged installer and according to the installation

instructions given below. The national and local rules

and regulations for placing and using wood-burning

stoves are equally applicable. WANDERS does not give

any guarantee if the Boreal is connected or installed

incompletely or incorrectly.

Connecting the ﬁreplace

Be sure that the ﬂoor is strong enough to hold the weight

of the hearth without problem.

Before mounting the hearth, follow the instructions

given in the previous chapter. Protect the ﬂoor when you

mount the stove, and mind your back.

1. Is the packing undamaged? If you detect any visible

damage, please notify the factory.

2. Is the chimney duct clean and open? (See the chap-

ter on ‘Preparation’.)

3. Is the air supply duct clean and open? (See the

chapter on ‘Preparation’.)

4. Are the ﬁre safety requirements met? (See the chap-

ter on ‘preparation’.)

5. Remove the screws for transportation safety.

6. Put the hearth in its position (Be sure not to damage

the ﬂoor and please mind your back while lifting!)

7. Secure the duct between the hearth and the exhaust

pipe. Connect it in the straightest possible way. The

ﬂue gas duct must be made of at least 2 mm steel.

Please note: the duct may expand by about 1 cm

per meter of its length. Ensure that the discharge

duct does not get jammed between the mouth of

the pipe and the ceiling. If this is the case with the

rotating stove, it will be harder to turn the stove.

8. Connect any external combustion air supply. If you

have the Boreal on a support, you must ﬁrst take

away the front cover.

9. Place the bafﬂe plate into the bafﬂe supports.

10. If you opted for the turn able model, you must

check whether the hearth can rotate smoothly. You

can check this by pulling the knob underneath the

hearth towards you and by turning the stove.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Boreal Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wanders Boreal

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info