Bedienungsanleitung Wanders Larix (Seite 20 von 72) (Deutsch, Englisch, Holländisch, Französisch)

694510

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

General

It is common practice for the dealer where you purchased your gas  replace to take also care of installing it and connecting it

to the gas mains. If this is not the case, please ensure that the installation is done by a certi ed installer. Connecting gas devices

by unquali ed persons is prohibited, in which case we cannot give any guarantee that your gas hearth is functioning properly.

Location of controls and receiver

To access the controls and the receiver, please take the

following steps;

• grab hold of the side of the lower frame,

• and carefully pull the frame toward you.

Here, you will  nd the gas control unit (Mertik GV60-M1

C5D3KL) and the receiver (Mertik GB60-R4AU).

Batteries (standard)

The batteries of the remote handset and the receiver

will last for about one year. We recommend that you use

alkaline batteries.

You need to replace them when the LED of the remote set

becomes dimmer and the word “BATT” appears in the display. The receiver will warn you if it’s batteries need to be exchanged.

You’ll hear, during ignition, a beep for 0.8 seconds followed by 0,2 seconds silence.

Replacing the batteries of the remote

Open the lid in the backside cover. Gently remove the 9V block battery and disconnect it from the contact holder. Avoid

pulling the cable. Connect the new battery, replace the set, and close the lid.

Replacing the batteries of the receiver

Carefully pull the entire receiver from the bottom of the stove. Slide open the cover and insert 4 new 1.5V batteries (type LR6

or AA). Please make sure to place the batteries in the receiver in the proper way. Then return the receiver to the stove.

Optional adapter

You can also choose to connect an adapter to the receiver (art. no. INK.3270). When using an adapter, you will no longer need

batteries and will have to remove them from the receiver. In the event of a power outage, you can still use the  replace by

inserting the batteries.

Setting the remote control handset (standard)

Once the batteries are placed, you need to set the electronic code (only when using it for the  rst time). Press the reset button

on the receiver until you hear 2 acoustic signs, and then release the reset button. Then press the small  ame button (2) within

20 seconds until you hear a long acoustic signal to con rm that the code has been set.

Setting the time

• Press the big- ame button (1) and the small-

 ame button (2) simultaneously, and the display

will show short  ashes to indicate that you are in

the set mode.

• When in the set mode, press the big- ame button

(1) to set the hours, and press the small- ame

button (2) to set the minutes.

• Wait or press the OFF button (3) to return to

manual control.

GV60-R4AU









Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Larix Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info