Bedienungsanleitung Wanders S75 (Seite 17 von 56) (Deutsch, Englisch, Holländisch, Französisch)

694502

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

easily using a slightly moist cloth once the stove has cooled. If necessary, use a special cleaning agent designed

for ceramic hobs. Do not touch the clean glass with your ngers. Fingerprints burn into the glass and can never

be removed.

After the rst couple of times using the stove, the cord in the door will expand to follow the contours of the stove.

HI2 Insides

The HI2 insides were specially developed for WFS and, without giving away too much of our

secret recipe, comprise a mix of special concrete with vermiculite. The heat-reective action

of the vermiculite generates heat build-up in the combustion chamber while the rest of the

material stores the heat.

Once combustion is well under way, you will see a perfect re – clean, eco-friendly combustion

with a high heat yield.

The re bricks, weighing in at some 30 kg, initially require thorough heating. The heat in the combustion chamber

is key to ensuring the stove works properly. We therefore advise getting the re going with thinner, more easily

combustible wood. Leave the doors slightly ajar for a quarter of an hour so the re quickly starts to burn ercely.

If you then ensure a red-hot bed of ash for further combustion, this will create decent ames and radiant heat that

you can enjoy for the rest of the evening, while occasionally adding fresh wood.

The heat is stored by the re bricks - known as accumulation - so any fresh logs ignite quickly. This accumulating

action means that the stove continues to give o heat for a long time after the re is extinguished.

The HI2 insides are made using water, so the moisture will have to be heated out of the re bricks during the rst

few sessions.

Our advice is to get a really good re going for the rst few hours. At that point, the re will probably not look like

it did in the showroom, but the appearance will improve rapidly after the rst couple of res.

After installation, it is essential that you rst allow your home to dry thoroughly. Inadequately

dried walls retain soot and other substances that are released by the stove during use. The risk

of cracks in the plaster is also highest at that point.

Fuel

The S60/S75 only burns on wood. Never place more than 2 kg (S 60) and 3 kg (S 75) of fuel in the re at once.

Always use clean, harvested timber that has been allowed to dry thoroughly. See the table below for drying times.

Moist wood burns poorly and generates far too much smoke. This can cover the glass of your stove with black

soot. Soot particles (creosote) also stick in your ue, which increases the risk of a chimney re.

Fresh, moist wood contains about 50% moisture. Cleaved wood still contains 20% moisture after drying it for a year

and moisture percentage will be decreased to 12 to 15% after drying it for two years. Dry wood gives nice ames

and little or no smoke, and the re will crackle when burning. Wet wood makes a hissing sound, gives much smoke

and only small ames which will considerably dampen the pleasure of burning your stove and the heat output.

Wood Drying time

Fir, Poplar 1 year

Lime, Willow, Spruce, Birch, Ash, Alder 1,5 years

Fruit trees, Beech 2 years

Elm 2,5 years

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders S75 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info