Bedienungsanleitung Wanders Solea (Seite 23 von 68) (Deutsch, Englisch, Holländisch, Französisch)

533291

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

can preset the desired temperature by the half degree

with the big buttons ▲ and ▼. The remote control will

automatically switch back to day-temperature setting.

The minimum day temperature is 5 degrees Celsius.

☽ - temp

Brieﬂy press the ‘SET’ button twice and the ☽-temp

will appear on the display. When you press and hold

the ‘SET’ button, the night-temperature indication will

start ﬂashing. You can preset the desired temperature

by the half degree with the big buttons ▲ and ▼. The

remote control will automatically switch back to night-

temperature setting. The minimum night temperature is

0 degrees Celsius. The display will then show the ‘- -‘

signal.

TIMER

You can preset a total of four time-settings. When you link

up all four time-settings, comfortable room temperatures

are ensured at all times.

Press ‘SET’ three times and the word ‘TIMER’ appears

on the lower right hand side of the display. Keep the

‘SET’ button pressed until the signal P1❂ appears and

the time indication is blinking. With the buttons ▲ and

▼ you can set respectively the hours and the minutes.

By brieﬂy pressing the ‘SET’ button you can browse

through the timer programme P1 ❂-temp, P1 ☽-temp,

P2 ❂-temp, P2 ☽-temp. Here is an example of a possible

presetting.

P1 ❂-temp: 07:30 - 08:30 19º C

P1 ☽-temp: 08:30 - 17:00 15º C

P2 ❂-temp: 17:00 - 23:00 19º C

P2 ☽-temp: 23:00 - 07:30 15º C

The TIMER function works only when the pilot ﬂame is

on. Press ‘OFF’ once to switch off the TIMER function.

The remote control will automatically switch to the

MAN position.

Thermostat

The remote control handset is also the thermostat of your

gas ﬁreplace. With the symbols ❂-temp and ☽-temp

you can preset the day and night temperatures. For the

optimum effect we advise you to use the handset remote

within a ﬁve-metre range, with the display pointed

directly at the ﬁreplace.

Lighting the ﬁre manually

Your Solea gas ﬁreplace can also be ignited manually.

Please follow the instructions given below.

1. Open the door of the ﬁreplace as shown on page 20.

Remove also the frontplate of the base.

2. Disconnect the ignition cable from the receiver and

connect it to the ignition block.

3. Turn the ‘0 I’ switch to the ‘I’ position. Turn the

motor switch all the way to the right until you hear a

ticking sound. Switch the operating switch to ‘MAN’

position.

4. Push a pen through the big hole against the small

metal bar and keep it pressed in. Press the small

square cube in the oriﬁce.

5. You will now hear a ticking sound and the pilot ﬂame

will ignite. When the pilot ﬂame is burning, keep

pressing against the small metal bar for about 10

seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Solea Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wanders Solea

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info