Bedienungsanleitung Wanders Tali (Seite 21 von 68) (Deutsch, Englisch, Holländisch, Französisch)

694512

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Switching o the appliance

• Press button  to lower the ames and to switch o the burner.

• Then press “OFF” button  to switch o the entire unit, including the pilot ame.

• If the appliance is not used for a longer period it is advisable that you turn o the gas valve in the gas pipe.

Important: if the pilot ame has gone out for whatever reason, you must wait at least 5 MINUTES before lighting

the pilot ame again.

Failure

If it looks as if the signals of the remote control are not properly received by the stove (receiver), it may be caused by:

• Empty batteries: change the batteries.

• An electronic problem: solve it by pressing the “RESET” button on the receiver.

• If the appliance often switches o you should contact your installer.

Operation (remote control with EcoWave)

For the complete explanation of the operation via the SYMAX-remote control, please refer to the instruction manual supplied

separately.

Operation (optional Wanders EcoWave app)

It is possible to order the optional Wi-Fi module in order to operate the replace using the Wanders EcoWave app,

The app can be downloaded for free at the Apple App Store and/or the Google Play Store. Incidentally, the app can only be

used in combination with the SYMAX EcoWave remote control.

Control (manual control)

If the batteries are due for replacement or if the receiver is defect, you can also operate the hearth by hand. To do so, you need

to disconnect the ignition (piezo) cable of the receiver and slide it gently onto the piezo connection of the gas control block.

Lighting the re and putting it out

1. Open the gas stopcock which is mounted in the gas pipe leading to the

appliance.

2. Press “O I” switch  on the gas control block in the “I” position.

3. Turn motor switch  on the gas control block all the way to the right. The

switch will make a ticking sound.

4. Turn operating switch  on the gas control block in the MAN position; an

orice  becomes visible.

5. Push the metal pin in the orice with something like a small pen. The gas

will now ow to the pilot.

6. While keeping the metal pin pressed in, press the (square) ignition fuse 

(next to the “O I” switch) to ignite the pilot ame. Look through the glass to

see whether the pilot ame is burning.

7. If the pilot ame is burning, keep the metal pin pressed for another 10

seconds and then release it. If the pilot ame dies, wait for another 5 minutes

before repeating the above steps.

8. Turn operation knob  to the “ON” position.

9. Turn motor switch  to the left to ignite the burner and to select the height

of the ames.

10. Turn motor switch  all the way to the right to put out the re; the pilot ame will keep burning.

11. If you want to put out the pilot ame as well, turn “O I” switch  to the “O” position.

12. Close the gas tap.











Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wanders Tali Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info