805484

Watts BT-PR02 - WIRELESS Plug MOUNTING RECEIVER Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
5
3. Installation
Install and connect the receiver respecting the following guidelines to guarantee an optimal reception:
- The receiver must be mounted at a minimum distance of 50cm of all others electrical or wireless materials
like GSM, Wi-Fi router.
- Wiring work related to the receiver must be carried out only when de-energized
- Connect your receiver to the power supply.
Depending on your installation, an order of pairing must be respected to ensure a correct RF signal transmission.
Installation 1: Receiver + RF thermostat
1. Switch on the receiver.
2. Press the RF button during 5 sec to switch to RF Init.
3. The RF LED should be Green fixed or orange blink indicating that the Receiver is now in radio configuration
mode waiting for a thermostat configuration address.
4. Please refer to the thermostat leaflet for enter the thermostat in “RF Init” mode.
5. The receiver RF LED must be switched OFF and the thermostat should exit the RF init mode to indicate
correct paring between both elements.
You can pair several receivers to the same RF thermostats
Note for installations 2 and 3: You can pair several receivers. Pay attention! Before linking a new receiver with the
Central unit, you have to reset the receiver imperatively.
Installation 2: Receiver + RF Thermostat + RF Central unit for heating regulation
1. First step is to pair the RF thermostat to the Central unit
2. Press the RF button on the receiver during 5sec.
3. The RF LED should be Green fixed or orange blink indicating that the Receiver is now in radio configuration
mode waiting for a central configuration address.
4. Please refer to the leaflet of the Central unit for more explanation about the pairing mode “RF Init”. You must
pair the Receiver as a heating device in the Central unit
5. The RF LED on the receiver will switch OFF and the Central will show a message to indicate correct pairing
between both elements.
You can pair several receivers in the same room.
Installation 3: Receiver + RF Central unit for ON/OFF or light control
1. Press the RF Button 5sec to switch the Receiver in RF Init mode .
2. The RF LED should be Green fixed or orange blink indicating that the Receiver is now in radio configuration
mode waiting for a central configuration address.
3. Please refer to the leaflet of the Central unit for more explanation about the pairing mode “RF Init”. You must
pair the Receiver as an ON/OFF plug or a light in the Central unit
4. The RF LED on the receiver will switch OFF and the Central will show a message to indicate correct pairing
between both elements.
You can pair several receivers in the same room. Receiver will work in Timer mode; you have the possibility to create a
weekly program for ON/OFF period.
Remarks:
- In case of a thermostat in RF Alarm, the receiver BT-PR02 RF stops heating.
- Plug receiver, Flush receiver, Wall receiver: The leds are switched off between 8pm and 8am when using a
BT-DP02 RF
4. Displosal and recycling information
Correct disposal of this product. This marking shown on the products indicates that it should not be disposed with
other household waste at the end of its worlking life.
Disposal of waste batteries: This product contain batteries. If so, use the separate collection for battery recycling. Do not
ut them with other household waste.
This device is suitable for use by children 8 years of age or older, and for persons with reduced physical, sensory or
mental abilities or lack of experience or knowledge, if they are properly supervised, or if instructions on the safe use of
the device have been given to them and the risks involved have been addressed. Children should not play with the
device. Cleaning and maintenance by the user should not be performed by unattended children.
5. Contact us
Watts Electronics S.A.S
B.P. N°10 - Z.A. des Tourettes
43800 ROSIERES
France T : +33(0) 471 57 40 49
F : +33(0) 471 57 40 90
www.wattsindustries.com
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Watts BT-PR02 - WIRELESS Plug MOUNTING RECEIVER wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info