Bedienungsanleitung Watts BT-WR02 - Live contact Wireless Wall receiver (Seite 3 von 20) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

805474

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

3. Installation and RF Initialisation rules

Install and connect the receiver respecting the following guidelines to guarantee an optimal reception:

- The receiver must be mounted at a minimum distance of 50cm of all others electrical or wireless materials like GSM, Wi-Fi

router.

- Wiring work related to the receiver must be carried out only when de-energized

- Connect your receiver to the power supply.

Depending on your installation, an order of pairing must be respected to ensure a correct RF signal transmission.

Installation 1: Receiver + RF thermostat

1. Switch on the receiver.

2. Press the RF button during 3 sec to switch to RF Init.

3. The RF LED should be Green ﬁxed or orange blink indicating that the Receiver is now in radio conﬁguration mode waiting for

a thermostat conﬁguration address.

4. Please refer to the thermostat leaﬂet for enter the thermostat in “RF Init” mode.

5. The receiver RF LED must be switched OFF and the thermostat should exit the RF init mode to indicate correct paring

between both elements.

You can pair several receivers to the same RF thermostats

Note for installations 2 and 3: You can pair several receivers. Pay attention! Before linking a new receiver with the

Central unit, you have to reset the receiver imperatively.

Installation 2: Receiver + RF Thermostat + RF Central unit for heating regulation

1. First step is to pair the RF thermostat to the Central unit

2. Press the RF button on the receiver during 3sec.

3. The RF LED should be Green ﬁxed or orange blink indicating that the Receiver is now in radio conﬁguration mode waiting for

a central conﬁguration address.

4. Please refer to the leaﬂet of the Central unit for more explanation about the pairing mode “RF Init”. You must pair the Receiver

as a heating device in the Central unit

5. The RF LED on the receiver will switch OFF and the Central will show a message to indicate correct pairing between both

elements.

You can pair several receivers in the same room.

Installation 3: Receiver + RF Central unit for ON/OFF or light control

1. Press the RF Button 3sec to switch the Receiver in RF Init mode .

2. The RF LED should be Green ﬁxed or orange blink indicating that the Receiver is now in radio conﬁgurationmode waiting for a

central conﬁguration address.

3. Please refer to the leaﬂet of the Central unit for more explanation about the pairing mode “RF Init”. You must pair the Receiver

as an ON/OFF plug or a light in the Central unit

4. The RF LED on the receiver will switch OFF and the Central will show a message to indicate correct pairing between both

elements.

You can pair several receivers in the same room. Receiver will work in Timer mode; you have the possibility to create a weekly

program for ON/OFF period.

Remarks:

- In case of a thermostat in RF Alarm, the receiver (BT-FR02 RF or BT-WR02 RF) will follow 20% cycle of heating to prevent the

installation against frost. (The receiver will stay in OFF mode if it was in OFF before the loss of RF communication).

- Plug receiver, Flush receiver, Wall receiver: The leds are switched off between 8pm and 8am when using a BT-DP02 RF / BT-

DP03 RF.

You can drive directly up to 2300W (10A) with your receiver BT-WR02 RF,

Mounting instruction:

- For security reason and easy mounting we recommend to connect only one radiator to each receiver.

- If your installation uses the pilot wire, don’t forget to active the Pilot Wire function on the parameter menu of BT-XX02 RF or

BT-XX03 RF thermostat.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Watts BT-WR02 - Live contact Wireless Wall receiver Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info