805518

Watts EFHT-LCD weekly Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/3
Nächste Seite
Your thermostat has one advanced menu.
1. In order to enter in this menu, use the joystick , and select the Timer mode ,
2. Then maintain the joystick on the left direction during 5 seconds.
3. The first parameter must be appears “N°01 SenS”
4. Use the joystick to to choose the parameter which needs to be adjusted.
5. Once the parameter chosen, press on the joystick , the value must be blink. You can now adjust the
value with the joystick . To valid your adjustment press the once again on the joystick .
6. To exit the parameter menu, go to the parameter « N°09 End » and press the joystick .
number
name
Parameter description
Factory setting
Other possibilities
01
SEnS
Selection of the sensor used for the regulation.
Sens
Air OnLy
Internal sensor
only
Sens
Flor OnLy
External sensor only
used as
Floor sensor or external
ambiance sensor.
02
CAL
Air
Calibration of the internal probe
The calibration must be done after 1 day working with the
same setting temperature in accordance with the following
description:
Put a thermometer in the room at 1.5M distance from the floor
(like the thermostat) and check the real temperature in the
room after 1 hour.
When you enter on the calibration parameter “no” is displayed
to indicate no calibration has made.
To enter the value read on the thermometer press on the
joystick, the message “_ _._” must be blink, now enter the
real value with the joystick « up and down » and valid your
adjustment by pressing the joystick.
The message “Done” should be displayed, the value will be
stored in the internal memory.
If you need to remake the calibration, enter once again on the
installation menu, and press on the joystick when the
message “Done” is displayed, then the message “_ _._”
should be blink.
The old value will be erased if you valid by pressing on the
joystick and the message “no” or will be replaced by the new
one.
* Pay attention:
Only the heating element managed by the thermostat must be
run during the complete step of the calibration.
no
no calibration
has made
done
Calibration has made
03
CAL
SoL
Calibration of the external probe
The calibration must be done same as described above if the
external sensor is connected and used like an external
ambiance sensor.
If the external sensor is used as floor sensor, the thermometer
should be put on the floor.
no
no calibration
has made
done
Calibration has made
04
1rst
Heat
Drying function (for cement, concrete floor…)
This first one heat works in the following way:
2 working hours dispatched on 24 hours the 1rst day and
1H00 more the following days, during 21 days.
During this period the room or floor in priority (if sensor
connected) temperature is limited at 20°C
no
Function not
activated
« 21 »
Function activated
* The function will be kept in
case of power supply cutting.
05
LoAd
Value of the power connected on the thermostat (in Watts)
Note:
1/ When the power connected on the thermostat exceeds >
2300W, you must use an external power relay (contactor).
Then adjust the parameter on “0000” position.
2/ When the external sensor is used for the regulation it’s not
necessary to adjust this parameter.
1500
Adjustable 0 to 3500W by
step of 50W
Your adjustments
Room :
________________
Installed power :
________________
09
End
To exit the installation menu
The software version is displayed.
Press on the joystick to exit
E760 4.xx
*Note :
Un menu « Expert » de paramétrage et de configuration avancé est aussi disponible dans votre thermostat.
INSTALLATION MENU
FUNCTION MODES DESCRIPTION
Use the joystick
to change the mode
TIMER Mode
Press the joystick
to enter in the TIMER mode.
Use the joystick to make blink the duration or the temperature.
When the value is blinking use the joystick to adjust:
- The duration with duration in hours « Hour » when it’s less than 24 h or in days « day ».
- The desired temperature for this duration (adjustable between 5 and 37°C)
To valid your adjustments press the joystick
.
To leave the TIMER mode before the end duration, press the
key.
COMFORT Mode
Use this function to set your installation in comfort mode.
Use the joystick to adjust the setting temperature. (Default setting 20°C)
AUTO Mode
The thermostat follows the chosen program in accordance with the actual hour.
By using the joystick , you can adapt the temperature until the next change within the program.
The symbol is displayed.
REDUCED Mode
Use this function to set your installation in comfort mode.
Use the joystick to adjust the setting temperature. (Default setting 18°C)
CLOCK ADJUSTEMENT Mode
Press the joystick
=> The first value which must be adjusted will be blink, djust the value with the joystick
Validate your adjustment by pressing on the joystick .
You could choose directly the value which must be adjusted with the joystick .
When you have finished press the joystick
to validate all your adjustments.
PROGRAM Mode
Press the joystick
=> The number of the current program blinks.
You can choose a program now by using the joystick .
By pressing the joystick
key, you can display the program either a built-in program (P1 to P5) or you
can create or modify a user’s program (U1 and U2). See the following section. For a built-in program (P1 to P5)
the program operates between the temperatures « comfort » and « reduced ».
Built-in programs descriptions.
P1: Morning, evening & weekend P3: 7h - 19h (office)) Evening & weekend P5: 8h - 19h, Saturday (Shop)
P2: Morning, noon, evening & weekend P4: Week-end (Secondary House)
Keyboard lock and unlock function
In
,
,
,
modes only. To lock the key board, maintains the joystick
pressed and press the
key at the same time, then the symbol “ “ appears.
To unlock the key board repeat this procedure, (the symbol “ “ will to disappear)
Error codes
Error on the External (Floor) sensor => Err and are blinks.
Error on the internal sensor => Err and are blinks.
Note: By safety if there is a sensor default the regulation is replaced by a rate of 5 % functioning.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Watts EFHT-LCD weekly wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info