Bedienungsanleitung Watts Solar Controller LCD PLUS (Seite 4 von 36) (Deutsch, Englisch)

805491

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

PRESENTATION (Display, keys)

1: Simplified drawing of the installation.

- The graphic of the pumps turn when they are

activated.

- The filled triangles on the valve graphic indicate

the circulation

2: Solar loading is in operation.

3: SD card storage is active.

4: Temperature of different sensors, Pumps speed

indications, Power and Energy quantity stored.

A: Keypad description

Navigation key up or plus key (+)

Navigation key down or minus key (-)

Navigation key left (◄)

Navigation key right (►)

Controller information Overview:

An information screen is available to allow you to view quickly

the status of all temperature sensors and outputs connected to

the controller.

From the main display, press (◄) once to display immediately.

The outputs & Inputs screen will be displayed for 1minute,

press (►) at any time to return to the main screen.

Main menu:

First of all press (►) to enter on the navigation menu.

(The title of the active menu is highlighted in black on the top of

the display)

When you enter on the navigation menu you can choose

another submenu by moving the selection cursor “” with the

keys (+) or (-), then you can enter this submenu with (►).

From all menus you can press (◄) to return to the previous

menu.

*ATTENTION:

As a safety feature, all critical parameters (System and Extra

function) are not programmable 4 hours after power on. If it is

necessary to modify these parameters, you must power-down

and power-up the controller. No settings are lost when

powering-down, or after a power failure.

After 4 hours it is only possible to alter system optimization

settings.

1 Quick start menu

The “Quick start menu” helps you to configure more easily the

main parameters of your solar controller after the initial

installation.

Power-up the controller and wait until the end of the

initialisation sequence. When the main screen is displayed,

press on the key (►) to access to the “service” menu. Then go

to the bottom of the menu and select the line “Quick start

menu” and press the navigation key (►) once to progress to

the quick start configuration.

The controller will guide you through the menu to configure the

main parameters, you will be prompted to adjust the parameter

value by pressing the (+) or (-) input. Press on the (►) key to

validate the display setting and skip to the next parameter.

The controller will return automatically to the main screen when

the configuration process is complete.

1 2

T1_ _

_°C

T2_ _

_°C

T3_ _

_°C

T4_ _

_°C

P1_ _ _

_ _ _

KWh

 Information -

T1 xxx°C T2 xxx°C T3 xxx°C

P1 xxx% P2 xxx% P3 x

 Information -

 Services

Settings

Operation

Operation h

Temperatures

 Service -

English

Time and date

System

Outputs Config.

Inputs Config.

Energy Measurements

Protection func.

Degrees °F

Tube collectors No

Factory setting No

 Quick Start menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Watts Solar Controller LCD PLUS Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info