Bedienungsanleitung WDH 9000K (Seite 10 von 55) (Deutsch, Englisch)

806986

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

- 9 -

USE

Before using the unit please look at our below installation instruction videos.

This machine adopts a unique energy storage system. It uses the stored cold or heat energy to run the unit for

cooling or heating function. Therefore, please complete cold storage or heat storage in advance before setting

the cooling mode / strong cooling mode or heating mode.

Do not activate the cold storage function in the room that you want to cool. A lot of heat will be blown into

the room during the cold storage function.

For best and fastest result position the unit near an open door or window during storage operation so the hot

air is ventilated out.

No energy storage is needed for dehumidification or ventilation function. You can press the mode button to

choose dehumidification mode or ventilation mode directly without proceeding cold storage or heat storage

in advance.

Notice: After switching on each mode, the fan inside the appliance will be running for 30 seconds first, and

then the appliance will work according to your desired mode function.

1. Connect the power supply

1) For the first use, please connect the power supply and then refer to step 2 of “Water inflow”.

2) When it is not used for the first time or there is water in the water tank, please insert the power plug

into the power socket and press the power button on the control panel.

2. Water inflow

In case of water shortage alarm (no water in the water tank during the first use or water shortage during

use), please follow the steps below to feed water into the water tank inside the machine.

1) Remove the water inlet knob at the back of the appliance by rotating it anti-clockwisely.

2) Use the water inlet/outlet hose to connect the machine with faucet. Press the water inflow button

and the faucet should be turned on at the same time.

3) When the water level reaches the working level, the water inlet valve will automatically close to

complete the water inlet.

4) Remove the water inlet/outlet hose and screw back the water inlet knob.

3. Cold storage

1) Press the mode button to select the cold storage function.

2) Press the button “+” or “-” to set the cold storage temperature. The lower the setting temperature is,

the greater the storage capacity is. Set the temperature range between -9℃ and 5℃.

3) After the completion of cold storage, the unit will automatically enter the standby state.

Note:

• During cold storage, the wind is at high speed and the swing blade is at the maximum outlet angle. At

this time, the heat energy will be discharged. In a narrow space, please open the doors and windows

for ventilation. Do not activate the cold storage function in the room that you want to cool. A lot of

heat will be blown into the room during the cold storage function. For best and fastest result position

the unit near an open door or window during storage operation so the hot air is ventilated out.

• The actual temperature of water in the water tank is displayed during cold storage.

• The air inlet and air outlet shall not be covered.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WDH 9000K Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info