Bedienungsanleitung Webasto Cool Top Trail 35 (Seite 7 von 168) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

802136

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Cool Top Trail 35 7

4.3 Different cut-out sizes

The installation is possible for different cut-out sizes:

a) Install instead of a 400x400mm roof hatch:

Dismount the roof hatch and use the remaining cut-

out. Remove sealant residue and unevenness. Fill in

screw holes with flexible non-hardening butyl body

sealant.

The adapter frame for 400x400mm cut-outs is part of

the scope of delivery.

b) Install instead of a 360x360mm roof hatch:

Dismount the roof hatch and use the remaining cut-

out. You need to buy the optional adaptor frame for

such cut-outs. It can be used instead of the

400x400mm adaptor frame.

Remove sealant residue and unevenness. Fill in screw

holes with flexible non-hardening butyl body sealant.

c) Create a new cut-out:

Since the adaptor frame for 400x400mm cut-outs is

part of the standard scope of supply this size may be

used.

If a smaller cut-out is preferred it is possible to buy as

accessory the 360x360mm adaptor frame and use

this one.

Consult the vehicle manufacturer for the most suitable

way and position to create a new cut-out.

4.4 Installation position

998

200

150

680

200

150

Fig. 01: Installation direction of the outdoor unit

Before the installation, consider the installation

position:

■Make sure that intended location does not interfere

with existing structures and cables.

■The air conditioner shall be installed as close as

possible to the centre of the roof.

■The installation position of the outdoor unit shall

be consistent with the traveling direction (F) of the

vehicle.

■Make sure that there is sucient room on the in-

side of the vehicle to install air distributor.

■Consider the installation position of the air distribu-

tor and ensure that outlets of the air distributor are

at least 400mm away from cupboards, walls and

bulkheads that can redirect conditioned air back

to the return air intake. If an outlet is closer than

400mm from an obstruction, then it should be

sealed closed. Failure to do this will result in a unit

that frequently cycles on and off.

■The cut-out shall avoid roof cladding joints where

ever possible.

■Chose an installation position between two longitu-

dinal supports or sections, if existing.

■There shall be a free space of 150mm minimum to

the sides of the unit and 200mm minimum to the

front and the back. the This to ensure suitable air

ﬂow and access for maintenance.

WARNING

When a hatch with safety ventilation func-

tion is replaced by the air conditioner it

must be ensured that the safety ventilation

is restored in another location.

NOTE

Angle of inclination of the air conditioner

shall not be greater than 5° (=8,8%) and

the rear of the air conditioner shall not be

higher than the front.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Cool Top Trail 35 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info