Bedienungsanleitung Webasto Cool Top Trail 36V (Seite 15 von 154) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

802137

Zoom out

Zoom in

Vorherige Seite

1/154

Nächste Seite

Operating Instructions | 5

9044618A_OI-II_Cool Top Trail 36V 15 / 154

5. Press the / button to set the hour when you

want the unit to switch off.

6. Press the HOUR/MIN button, and then press the /

button to set the minutes.

7. To end the setting mode press the SET TIME button again.

The clock time is shown. Alternatively, 10 seconds until the

digits stop flashing.

NOTE

You have now set the timer ON and OFF times, but

these must be activated separately. See chapter5.13,

"Activating the timer" on page 15.

Fig.38 Setting the timer

5.13 Activating the timer

Before activating the timer, select the operation mode, the set

temperature, and the desired fan level.

After the start and stop times are set (see chapter5.12, "Setting

the timer" on page 14) one of the three different TIMER modes

can be activated:

lTIMER ON mode

In this mode the unit will switch on at the desired ON time

and keep on running.

lTIMER OFF mode

In this mode the unit will stop running at the desired OFF

time and will stay off.

lTIMER ON / OFF mode

In this mode the unit will start to run at the ON time and

stop running at the OFF time. This pattern will be repeated

every day.

Fig.39 TIMER Modes

1. Press the TIMER button repeatedly until either the ON or

OFF or both symbols are flashing depending on which timer

mode is preferred.

2. To confirm the selection wait 10 seconds until the symbol

stops flashing and is shown permanently. The clock time is

now displayed again.

Fig.40 Activating the timer

NOTE

If the clock is displayed without an ON / OFF icon, then

you have not activated the timer.

5.14 Setting the sleep function

The sleep function automatically modifies the target temperat-

ure to provide a comfortable sleeping temperature. This also

helps to reduce compressor run time, energy consumption and

noise levels.

1. Press the SLEEP button to activate the sleep function.

– The icon is displayed in the display of the remote con-

trol to indicate that the sleep function is activated.

– In COOL mode the set temperature will automatically in-

crease in two steps and it will have increased by 2°C

after two hours.

– In HEAT mode the set temperature will automatically de-

crease in three steps and it will have decreased by 3°C

after two hours.

– The sleep function is only available in COOL or HEAT

mode.

2. Press the SLEEP button again to deactivate the sleep func-

tion.

Fig.41 Setting the sleep function

5.15 Changing the units of temperature

Press the °C/°F button to select which temperature unit you

want to be displayed: Celsius or Fahrenheit.

lYou can do this in any mode.

lThe display on the air distributor follows the selection made

on the remote control.

Fig.42 Celsius / Fahrenheit selection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Cool Top Trail 36V Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info