Bedienungsanleitung Webasto Dual Top ST 8 (Seite 7 von 19) (Englisch)

802472

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Operating instructions | 4

9026381C Dual Top ST 6 _ 8 - OI 7 / 19

Ad 6 The power indicator lights up green when the

Dual Top ST is switched on and START (3) is pressed.

Also “Heater ON” on display (7). The heater is

operating or in the standby mode.

Power indicator is off when STOP (3) is pressed or

when Dual Top ST is switched off. Also “Heater OFF”

on display (7). The heater is not operating or is not in

the standby mode.

The indicator flashing pulses red if a fault has oc-

curred.

Ad 7 The heater is ON when the Dual Top ST is switched on

and START (3) is pressed. The heater is operating or

in the standby mode.

The heater is OFF when STOP (3) is pressed or the

Dual Top ST is switched off. The heater is not operat-

ing or is not in the standby mode.

Ad 8 The remote symbol is shown when the device is

ready to accept signals from the remote control.

Ad 9 The drainage symbol is shown when the electrical

safety/drainage valve is opened.

Ad 10 Dual Top ST 8:

The 230 V symbol is shown when the external

230 V power supply is connected.

The 230 V symbol is shown if it is not connected.

Dual Top ST 6:

The desired interior temperature is shown, not the ac-

tual temperature.

Ad 11 The desired interior temperature is shown, not the ac-

tual temperature.

Ad 13 Dual Top ST 8:

The desired water temperature is shown, not the ac-

tual temperature.

CAUTION

The absence of the " 230 V" symbol does not guar-

antee that no 230 V supply is present!

Background lighting

The background lighting in the display comes on when you

switch the Dual Top ST equipment on. It does not matter if the

heater is in operation or not. The background lighting fades out

after a few minutes if you do not press any buttons.

The backlight comes back on if you press or .

NOTE

The display may become darker when the control panel

temperature becomes very high or when the control

panel is placed in direct sunlight. Avoid exposing the

control panel to high temperatures or direct sunlight.

Where these conditions cannot be avoided, adjust the

display contrast in “ Setup” (see chapter4.4.2, "Lan-

guage, temperature unit, hour format, display contrast"

on page 11 ).

4.2 Manual control panel Dual Top ST

4.2.1 Summer mode (hot water only)

1. Make sure that the boiler is filled with fresh drinking water.

2. Set selector knob (A) to summer mode, water temperature

40 °C (1) or 70 °C (2) on the control panel.

The indicator (C) on the control panel lights up green when the

equipment is switched on. The red indicator on the mode se-

lector knob (A) illuminates.

When the selected water temperature is reached (40 °C or 70

°C) combustion inside the heater stops.

As soon as the water temperature drops below a certain value,

combustion is started again.

The indicator (C) on the control panel lights up green as long as

the equipmend is switched on.

4.2.2 Winter mode (heating without hot water

production)

1. Set the interior temperature selector (B) on the control

panel to the desired thermostat setting for interior temper-

ature.

2. Set the mode selector knob (A) on the control panel to

winter mode, heating without hot water production (3).

The indicator (C) on the control panel lights up green when the

equipment is switched on.

The red indicator on the mode selector knob (A) and on the in-

terior temperature selector (B) both illuminate.

When the selected interior temperature is approached, the

heater starts to modulate.

The power is adjusted to a level necessary to maintain a con-

stant temperature.

In case the interior temperature exceeds the selected temperat-

ure, due to environmental influences, the combustion inside the

heater stops.

NOTE

Please note that, if the boiler has been filled, the water

is automatically heated as well. The water temperature

may reach up to 80 °C depending on the power and

the duration of the heating.

4.2.3 Winter mode (heating with hot water

production)

1. Make sure that the boiler is filled with fresh drinking water.

2. Set the interior temperature selector (B) on the control

panel to the desired thermostat setting for room temperat-

ure.

3. Set the mode selector knob (A) on the control panel to

winter mode, heating with hot water production (4).

The indicator (C) on the control panel lights up green when the

equipment is switched on.

The red indicator on the mode selector knob (A) and on the in-

terior temperature selector (B) both illuminate.

The heater gradually reduces the power until the selected in-

terior temperature is reached. If the interior temperature has

been reached, but the water temperature is still too low, the

blown air circulation fan switches off and the water continues

to be heated to a temperature of 70 °C.

The water temperature may reach up to 80 °C depending on

the heating power that is required to achieve the interior tem-

perature.

NO WATER control

When winter mode (heating with hot water production) is se-

lected, but the boiler has no water, there will be a warning on

the control panel.

The green LED with the winter mode icon, heating without hot

water production (3), will flash.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Dual Top ST 8 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Dual Top ST 8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info