Bedienungsanleitung Webasto Go (Seite 6 von 12) (Englisch)

802121

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

4 | Installation

6 / 12 5911743-A-01 Webasto Go

ger module detects an output ground fault, it will shut

down power to the output cable and illuminate the RED in-

dicator.

lInsulation: The charger module, adapter, cable assembly,

and charge coupler are completely insulated (no exposed

live parts) to protect against electric shock.

lUnintentional Disconnection: The charge coupler is de-

signed to minimize unintentional disconnection. A pilot sig-

nal wire in the cable and charge coupler eliminates the pos-

sibility of electric shock when not connected to a vehicle or

if an unintended disconnect occurs during a charge. Dis-

connection during charging is safe.

4 Installation

Fig.6 Wall hanger

1Wall hanger

1. Choose a location to install the wall hanger.

NOTE

The Webasto Go Mobile Charger can be used indoors

and outdoors.

NOTE

The hanger should be located in practical proximity to

both the utility receptacle or plug, and the location of

your vehicle’s charge receptacle, preferably mounted to

a wall stud.

Drywall and masonry wall installations require the use

of appropriate fasteners.

2. Measure up approximately 8 inches / 20 cm from the de-

sired receptacle and mark the location.

NOTE

Before drilling any holes, verify that the control box will

sit in hanger after it is plugged in.

3. Drill out the preferred mounting holes through the back of

the wall hanger using a 7/32 inch / 5.6 mm drill bit.

4. Using a screwdriver, tighten the screws for the wall hanger.

5 Using your Webasto Go

Mobile Charger

5.1 Indicator light

Fig.7 Webasto Go Mobile Charger

1Indicator light

The indicator light on your charger is the first thing you will no-

tice when you are about to plug or unplug your vehicle. Before

getting started, here is a simple explanation of the indicators.

AMBER Indicator

The AMBER Indicator illuminates to indicate the charger is re-

booting after an error. Refer to the chapter8.1, "Troubleshoot-

ing" on page 9 for more information.

BLUE Indicator

When plugged into the wall socket, the BLUE Indicator illumin-

ates to indicate the charger is ready to use. During charging, the

BLUE Indicator will pulse on and off every two seconds. Refer to

the chapter8.1, "Troubleshooting" on page 9 for more in-

formation.

RED Indicator

The RED Indicator illuminates when the charger detects an er-

ror. If the RED Indicator illuminates, the charger will not deliver

power to the vehicle. The error must be corrected before a

charging cycle can begin or continue. Refer to the chapter8.1,

"Troubleshooting" on page 9 for more information.

5.2 Charging Your Vehicle

4 3

Fig.8 Webasto Go Mobile Charger

1Type 1 IEC Coupler 2Type 2 SAE Coupler

3Low Power Adapter 4High Power Adapter

NOTE

If Wall bracket is not used for mounting the cordset,

plug cordset to wall socket closer to ground.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Go Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Go

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info