Bedienungsanleitung Webasto Live (Seite 29 von 79) (Deutsch, Englisch, Holländisch, Italienisch, Spanisch)

802116

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

5110326C_OI-II_Webasto Live 17

6Installation and electrical

connection

Observe the safety information provided here chapter2,

"Safety" on page 14.

NOTE

In addition to these operating and installation instruc-

tions, follow and comply with the local regulations re-

lating to operation, installation and environmental

protection.

6.1 Requirements installation space

The following points must be take into account when se-

lecting the installation location for the Webasto Live:

– The lower edge of the enclosed mounting template

must be a minimum distance above the ground during

installation. The minimum distance is indicated in the

figure at chapter13, "Assembly" on page 22.

– If several charging stations are installed next to each

other, a spacing of at least 200 mm must be main-

tained between each station.

– The mounting surface must be solid and strong.

– The mounting surface must be completely flat (max. 1

mm difference between the individual mounting

points).

– The mounting surface must not contain any flam-

mable substances.

– The normal parking position of the vehicle.

– The location of the charging plug on the vehicle.

– A cable run from the charging station to the vehicle as

short as possible.

– No risk of driving over the charging cable.

– Possible electrical connections.

– Pavements and escape routes must not be obstructed.

– Reception via WLAN or UMTS exists.

– Protected against direct solar radiation and rain for

optimum and fault-free operation.

– Compliance with local regulations such as garage reg-

ulations or fire protection regulations.

6.2 Criteria for the electrical connection

The maximum charging current that can be configured is

indicated on the type label of the charging station. The

type label is on the right-hand side of the charging sta-

tion.

The power availability in the service connection determ-

ines the maximum permitted charging current. The elec-

trician makes the necessary settings in the configuration.

(see online configuration instructions: https://webasto-

charging.com/documentation)

Before connecting, have the prerequisites for connection

checked by an electrician. Comply with the nationally ap-

plicable regulations of the authorities and power supply

companies, e.g. registration of installation of a charging

station.

All protective devices specified must be designed such

that every power supply pole of the charging station is

disconnected in the case of a fault. When selecting the

protective device, you must use the national installation

regulations and standards.

6.2.1 Dimensioning of the Residual Current

Circuit Breaker (RCCB)

The national installation regulations generally apply. Un-

less otherwise specified therein, each charging station

must be protected by an appropriate residual current

device (RCD) with a trip current of ≤30mA.

Suitable residual current devices are a type-B RCD or a

type-A RCD with a residual direct current detecting

device (RDC-DD) according to IEC62955. A suitable type-

A RCD with integrated residual DC detection is, for ex-

ample, the residual circuit current breaker type

DFS4AEV from Doepke.

The rated residual current must not be greater than

30mA. Whenever a charging station is protected using a

Type B ground fault circuit interrupter (GFCI), every up-

stream GFCI, even if not assigned to the charging station,

must either by a Type B unit, or be equipped with a DC

ground fault detection unit.

6.2.2 Dimensioning of the circuit breaker

The circuit breaker must conform to IEC 60898. The let-

through energy (I²t) must not exceed a maximum 80,000

A²s.

Alternatively, a residual current circuit breaker combina-

tion (RCBO) according to EN 61009-1 can be used. The

aforementioned parameters apply for this circuit breaker

combination.

6.2.3 Mains isolation device

The charging station does not have its own main ON/OFF

switch. The protective devices installed in the power sup-

ply system are therefore also used to disconnect the

power supply.

6.2.4 Dimensioning the cross section of the lead

The electrician determines the conductor cross section,

see chapter14, "Technical data" on page 23.

The cross section of the lead is dependent on:

– the maximum power availability from the service con-

nection.

– the length of the cable.

6.3 Installation

See also chapter13, "Assembly" on page 22. The sup-

plied installation material is intended for mounting the

charging station on a concrete wall or on an external

stand. For installation on a stand, the mounting material

is included in the scope of delivery of the stand.

üScope of delivery is checked for completeness.

uTake into account the mounting position at the install-

ation location. See Fig. 14.

uRemove the drill template at the perforation from the

packaging.

uMark the four positions of the drill holes at the install-

ation location using the drill template. See Fig. 14.

uDrill 4x8mm drill holes in the marked positions.

uMount the wall-mounting bracket in position over the

upper holes using 2 wall plugs and 2 screws,

6x70mm, T25.

Webasto Live Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Live

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info