Bedienungsanleitung Webasto Thermo Pro 90 HDD (Seite 3 von 6) (Englisch)

802495

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Liability claims:

– Failure to observe the operating instructions and the infor-

mation contained in it will result in a disclaimer of liability by

Webasto.

The same applies if repairs are carried out incorrectly or with the

use of parts other than genuine spare parts. This will result in

the invalidation of the type approval for the heater and there-

fore of its general operating licence/EC type approval.

– Liability claims can only be asserted for proven compliance with

the maintenance and safety instructions by the applicant.

Operating Heater

Before switching on the heater (with the ignition on), the vehicle heating system should be set

to “warm” and the vehicle heating blower should be set to the slowest setting (lower power

consumption). Depending on the type of vehicle, the air-conditioning system can perform these

settings automatically or partly autonomously. Please ask your specialist dealer to explain the

optimum settings.

For ADR hazardous material vehicles only:

The Thermo Pro 90 HDD heater is switched on and off manually by means of a switch.

Automatic controllers are prohibited. In vehicles of the type FL, the operation of these heaters

is prohibited during loading and unloading and at the loading points. The generator signal and

auxiliary drive signal are requested for this purpose.

In vehicles of type FL, the heaters are automatically switched off and the maximum ADR after-

running time is 40s in accordance with the legal speciﬁcations.

An ADR afterrunning period takes place if:

– the generator signal (D+) is discontinued or

– the auxiliary drive signal (e.g. pumping device) is present.

After the end of the ADR afterrunning period, the control unit is in ADR locking mode.

The heater can be restarted by switching it off and on again using the “ON/OFF” switch. This

will not work while the pumping device belonging to the vehicle is in operation. The ADR

lock will not be cancelled if the “ON/OFF” switch is activated and the operating voltage Ub is

removed and reapplied.

The disconnector (emergency off switch) may only be actuated in the event of danger since the

heater will be switched off without afterrunning period (possible overheating).

Heater operation:

If the heater is switched on with a cold engine, the heater starts up in a low load range and

then increases the power. Depending on temperature, this process can take approx. 2 minutes.

The coolant temperature is controlled automatically throughout operation. The heater can also

be switched on while travelling. The vehicle blower is only switched on when the coolant tem-

perature is at around 30°C, avoiding unnecessary energy consumption. There is thus a delay in

starting the vehicle blower, depending on the temperature. When switching off the heater, a

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Thermo Pro 90 HDD Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Thermo Pro 90 HDD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info