Bedienungsanleitung Weber genesis e 310 (Seite 10 von 64) (Englisch, Französisch)

328034

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

GAS INSTRUcTIoNS

Remove Control Knobs & Control Panel for Leak Testing

You will need: Phillips & flathead screwdrivers.

A) Locate door pin release in door assembly. Using a screwdriver, push down on door

pin release (1) until door detaches from frame assembly. Pull top of door away from

frame assembly (2) and lift door off bottom adjustable hinge pin.

B) Remove control knobs, igniter button, retention nut, and battery (3).

C) Remove screws from wind deflector with a Phillips screwdriver (4).

D) Tilt end of wind deflector down and slide wind deflector away to remove (5).

E) Let igniter module dangle from wires. Do not disconnect (6).

F) Remove screws from underside of control panel with Phillips screwdriver (7).

G) Lift control panel up slightly, tilt up front edge and gently lift up (8).

H) Replace control panel and wind deflector when leak check is completed.

◆

CHECK FOR GAS LEAKS

Note: All factory-made connections have been thoroughly checked for gas leaks. The

burners have been flame-tested. As a safety precaution, however, you should recheck

all fittings for leaks before using your Weber® gas barbecue. Shipping and handling

may loosen or damage a gas fitting.

m WARNING: The gas connections of your gas grill have been

factory tested. We do however recommend that you leak

check all gas connections before operating your gas grill.

m WARNING: Perform these leak checks even if your barbecue

was dealer or store assembled.

If your grill has a side burner, make sure the side burner is turned off.

Turn on gas supply at source.

m WARNING: Do not ignite burners when leak checking.

You will need: A soap and water solution and a rag or brush to apply it.

A) Mix soap and water.

B) Turn on gas supply (1).

C) Check for leaks by wetting the fitting with the soap and water solution and watching

for bubbles. If bubbles form, or if a bubble grows, there is a leak.

If there is a leak, turn off the gas and tighten the fitting. Turn the gas back on and

recheck with the soap and water solution. If leak does not stop, do not use the

barbecue. Contact the Customer Service representative in your area using the

contact information on our web site. Log onto www.weber.com

D) When leak checking is complete, turn gas supply off at the source and rinse

connections with water.

Note: Since some leak test solutions, including soap and water, may be slightly

corrosive, all connections should be rinsed with water after checking for leaks.

m WARNING: You should check for gas leaks every time you

disconnect and reconnect a gas fitting.

m DANGER

Do not use an open flame to check for gas leaks. Be sure

there are no sparks or open flames in the area while you

check for leaks. Sparks or open flames will result in a fire or

explosion, which can cause serious bodily injury or death

and damage to property.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Weber genesis e 310 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Weber genesis e 310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info