conjunction with the smell of gas. (This is normal for
the burner lighting tube).
Inspect Spider/Insect screens for possible obstructions
(blockage of holes).
Clean Spider/Insect screens. Refer to “ANNUAL
MAINTENANCE”.
Symptoms:
Burners do not light, or Burners have a small flickering
flame in the HI position, or Grill temperature only
reaches 250° to 300° in the HI position.
Some countries have regulators with an excess gas flow
safety device.
The excess gas flow safety device, which is part of the
grill-to-cylinder connection, may have been activated.
To reset the excess gas flow safety device, turn all burner
control knobs and the cylinder valve off. Disconnect
the regulator from the cylinder. Turn burner control
knobs to HI. Wait at least 1 minute. Turn burner control
knobs to OFF. Reconnect the regulator to the cylinder.
Turn cylinder valve on slowly. Refer to “MAIN BURNER
IGNITION”.
Burner does not light, or flame is low in HI position.Is LP fuel low or empty?Refill LP cylinder.
Is fuel hose bent or kinked?Straighten fuel hose.
Does burner light with a match?If you can light burner with a match, then check the
ignition system.
Did you use the snap igniter several times until the main
burner lit? Refer to “MAIN BURNER IGNITION”.
Make sure you hold the control knob in for two seconds
after snapping the igniter and seeing the orange flame
from the burner lighting tube.
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
Try manually lighting the burner. Refer to “MAIN
BURNER MANUAL IGNITION”. Call Customer Service.
Experiencing flare-ups:
mCAUTION: Do not line the slide-out
grease tray with aluminum foil.
Are you preheating grill in the prescribed manner?All burners on HI for 10 to 15 minutes for preheating.
Are the cooking grates and Flavorizer
™
bars heavily
coated with burned-on grease?
Clean thoroughly. Refer to “CLEANING”.
Is the slide-out grease tray dirty and not allowing grease
to flow into catch pan?
Clean slide-out grease tray.
Burner flame pattern is erratic. Flame is low when
burner is on HI. Flames do not run the whole length of
the burner tube.
Are burners clean?Clean burners. Refer to “MAINTENANCE”.
Inside of lid appears to be “peeling.” (Resembles paint
peeling.)
The lid is porcelain enamel or stainless steel, not paint.
It cannot “peel”. What you are seeing is baked on grease
that has turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
Clean thoroughly. Refer to “CLEANING”.
Cabinet doors are not aligned.Check the adjustment pin on the bottom of each door.Loosen adjustment nut(s). Slide door(s) until aligned.
Tighten nut.
Grill seems to lose heat when cooking in cold weather
temperatures of 10°C (50°F) or colder.
Is there frost/ice on the outside of the LP cylinder?The liquid propane in the cylinder turns to vapour too
slowly to supply the burners with gas. This is due to the
air temperature cooling the LP cylinder, which slows the
vaporisation process. Turn off burner control knobs and
the LP cylinder. Replace with a spare LP cylinder and
resume cooking.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com.
PROBLEMCHECKSOLUTION
Side Burner does not light.
Some countries have regulators with an excess gas flow
safety device.
Is gas supply off?
The excess gas flow safety device, which is part of
the grill-to-cylinder connection, may have been
activated.
Turn gas supply on.
To reset the excess gas flow safety device close the LP tank
valve and turn all burner control knobs to the OFF position.
Open the grill and side burner lids. Slowly turn the LP tank
valve until it is completely open. Wait several seconds then
ignite your side burner. Refer to “SIDE BURNER IGNITION”.
Flame is low in HI position.Is the fuel hose bent or kinked?Straighten hose.
Push button ignition does not work.Does burner light with a match?If match lights burner, check igniter. Refer to “SIDE BURNER
MAINTENANCE”.
Is there a fresh battery installed?Verify that the battery is in good condition and installed correctly.
Refer to “ELECTRONIC IGNITION SYSTEM OPERATIONS.”
Are the wires connected properly to the igniter
module?
Be sure that wires are correctly inserted into terminals on
ignition box. Refer to “SIDE BURNER MAINTENANCE.”
Is there plastic wrapping around the new battery?Remove plastic wrapping.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Weber Summit E-670 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
