Bedienungsanleitung Weldkar MIG 2125 INVERTER WELDER (Seite 14 von 44) (Deutsch, Englisch, Holländisch, Französisch)

686265

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

INVERTER WELDER WK MIG 2125

1414

welding arc. If this is not possible, tightly cover

them with approved covers.

4. Be alert that welding sparks and hot materials from

welding can easily go through small cracks and

openings to adjacent areas.

5. Watch for ﬁre, and keep a ﬁre extinguisher nearby.

6. Be aware that welding on a ceiling, ﬂoor, bulkhead,

or partition can cause ﬁre on the hidden side.

7. Do not weld on closed containers such as tanks or

drums.

8. Connect work cable to the work as close to the

welding area as practical to prevent welding current

from travelling long, possibly unknown paths and

causing electric shock and ﬁre hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder or cut off

welding wire at contact tip when not in use.

WARNING

FLYING SPARKS AND HOT METAL

can cause injury.

Chipping and grinding cause ﬂying metal.

As welds cool, they can throw off slag.

1. Wear approved face shield or safety goggles. Side

shields recommended.

2. Wear proper body protection to protect skin.

WARNING

CYLINDERS can explode

if damaged.

Shielding gas cylinders contain gas under high pressure.

If damaged, a cylinder can explode. Since gas cylinders

are normally part of the welding process, be sure to

treat them carefully.

1. Protect compressed gas cylinders from excessive

heat, mechanical shocks, and arcs.

2. Install and secure cylinders in an upright position by

chaining them to a stationary support or equipment

cylinder rack to prevent falling or tipping.

3. Keep cylinders away from any welding or other

electrical circuits.

4. Never allow a welding electrode to touch any

cylinder.

5. Use only correct shielding gas cylinders, regulators,

hoses, and ﬁttings designed for the speciﬁc

application; maintain them and associated parts in

good condition.

6. Turn face away from valve outlet when opening

cylinder valve.

7. Keep protective cap in place over valve except when

cylinder is in use or connected for use.

8. Read and follow instructions on compressed gas

cylinders, associated equipment, and Safety

Standards.

WARNING

MOVING PARTS

can cause injury

Moving parts, such as fans, rotors, and belts can cut

ﬁngers and hands and catch loose clothing.

1. Keep all doors, panels, covers, and guards closed

and securely in place.

2. Stop engine before installing or connecting unit.

3. Have only qualiﬁed people remove guards or covers

for maintenance and troubleshooting as necessary.

4. To prevent accidental starting during servicing,

disconnect negative (-) battery cable from battery.

5. Keep hands, hair, loose clothing, and tools away

from moving parts.

6. Reinstall panels or guards and close doors when

servicing is ﬁnished and before starting engine.

WARNING

SPARKS can cause BATTERY GASES

TO EXPLODE; BATTERY ACID can burn

eyes and skin.

Batteries contain acid and generate explosive gases.

1. Always wear a face shield when working on a

battery.

2. Stop engine before disconnecting or connecting

battery cables.

3. Do not allow tools to cause sparks when working on

a battery.

4. Do not use welder to charge batteries or jump start

vehicles.

5. Observe correct polarity (+ and –) on batteries.

NOTE

Considerations about welding and the effects

of LOW FREQUENCY ELECTRIC AND MAGNETIC

FIELDS

Electric current following through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding/

cutting current creates EMF ﬁelds around cables and

power sources.

The magnetic ﬁelds created by high currents may affect

the operation of pacemakers. Wearers of vital electronic

equipment (pacemakers) shall consult their physician

before beginning any arc welding, cutting, gouging or

spot welding operations.

Exposure to EMF ﬁelds in welding/cutting may have

other health effects which are now not known.

To reduce magnetic ﬁelds in the workplace, use the

following procedures.

1. Keep cables close together by twisting or taping

them.

2. Arrange cables to one side and away from the

operator.

3. Do not coil or drape cable around the body.

4. Keep welding Power Source and cables as far away

from body as practical

WARNING

ABOUT PACEMAKERS

The above procedures are among those

also normally recommended for pacemaker wearers.

Consult your doctor for complete information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Weldkar MIG 2125 INVERTER WELDER Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info