Bedienungsanleitung Wellis Sand Filter (Seite 8 von 76) (Deutsch, Englisch, Französisch)

784894

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Assembly

Note: Since all connections have gaskets, there is no need to tighten the nuts too much. This could damage plastic

parts.

Note: You’ll need a cross-point screwdriver for the assembly.

1. Mounting of the drainage bolting into the vessel.

Put the threaded counterpart through the vessel’s drainage opening from the inside (FIG. 1.1). Put a gasket

over the protruding thread and screw the socket on (FIG. 1.2). Put the sand strainer into it. Push the strainer inside

by screwing on the lid with the sealing O-ring (FIG. 1.3). Hand-tightening is sufficient for connection sealing. You

might damage the parts if you use pliers.

1.A For 10L vessels with drainage sockets, proceed as follows:

Put the drainage strainer through the vessel’s drainage opening from the inside (FIG. 1.4). Screw the lid with

a gasket onto the socket (FIG. 1.5). Hand-tightening is sufficient for connection sealing. You might damage the

parts if you use pliers.

2. Suction basket completion

Connect the basket bottom to the suction basket itself by snapping in the 6 locks around its circumference.

Put a suction pipe into the completed suction basket (FIG. 2.1). Put the unit into the empty vessel (FIG. 2.2) and

fix its position by putting the hopper on (FIG. 2.3). The vessel is now ready for filling.

3. Filling with Sand

Prior to the filling, we recommend that you put the vessel onto the pump platform. The filled vessel is difficult

to handle. Fit the vessel side skims with the skims in the stand; the drainage bolting must point away from the

switch (FIG. 3.1).

With the hopper put on, fill the vessel with a required amount of sand (FIG. 3.2). The sand level in the vessel

should be reaching the top of the side skims (FIG. 3.3). Afterwards, take the hopper off and remove grains of sand

and other impurities from the sealing surface of the vessel socket.

4. Multiport Valve Installation

Put an O-ring through the bottom of the valve and put the valve onto the socket of the filled vessel. Direct the

valve so that its PUMP/ČERP socket is pointing in the same direction as the pump outlet in the vessel stand.

Afterwards, put both sleeve halves onto the vessel recess, connect with bolts (FIG. 4.3) and tighten evenly.

Insert a small rubber gasket into the pressure gauge opening, screw the pressure gauge body (FIG. 4.1) on

with your hand and tighten lightly.

!!! Make sure the screwing is done properly; otherwise, you may damage the fine thread!!!

Screw the lid with a gasket onto the WASTE/ODPAD port (FIG. 4.2).

5. Connection Hose Installation

Put the constraining clamps onto the hose, put elbows with swivel nuts into both ends of the hose (FIG. 5.1).

Insert the particle grate into the side outlet of the pump (FIG. 5.2), ; afterwards connect the prepared hose to

this outlet and the PUMP/ČERP port of the valve using swivel nuts and gaskets (FIG. 5.3).

!!! The hose clamps are only to be tightened once the swivel nuts have been tightened!!!

6. Prefilter and Arbour Assembly

Mount the transparent prefilter onto the suction socket of the pump and then mount the hose connection

arbour onto the prefilter (FIG. 6.1).

!!! Pay attention to the shape of the used gasket!!!

6.A For Azuro 6m3/h + Timer filtering equipment with a large prefilter, proceed as follows:

Pull the prefilter body along with a gasket over the pump socket and fix using a swivel nut inside the prefilter;

put the impurity basket into the prefilter and close with a lid with the O-ring. Use a swivel nut to mount the elbow

with a gasket onto the socket (FIG. 6.2).

!!! Pay attention to the shape of the used gasket!!!

Screw the second connecting hose arbour onto the POOL/BAZÉN port of the valve (FIG. 6.3) / elbow (FIG. 6.4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wellis Sand Filter Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info