Bedienungsanleitung Westfire WF32 (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

813316

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

WESTFIRE · WF32 WESTFIRE · WF32

These instructions cover the basic principles to ensure the satisfactory installation of the WESTFIRE WF32/

UNIQ 32 inset wood stove, although detail may need slight modiﬁcation to suit particular local site conditions.

In all cases the installation must comply with current Building Regulations, Local Authority Byelaws and other

speciﬁcations or regulations as they affect the installation of the stove.

It should be noted that the Building Regulations requirements may be met by adopting the relevant recom-

mendations given in British Standards BS 8303, BSEN15287 as an alternative means to achieve an equivalent

level of performance to that obtained following the guidance given in Approved Document J.

STOVE PERFORMANCE & TESTING

The WESTFIRE WF32/UNIQ32 insets have been approved in accordance with EN 13240.

Nominal heat output

Stove model Weight Wood Smokeless fuels

WF32/UNIQ32 INSET 112 kg 7.0 KW N/A

PREPARATORY WORK AND SAFETY CHECKS – IMPORTANT WARNING

This stove must not be installed into a chimney that serves any other heating appliance.

There must not be an extractor fan ﬁtted in the same room as the stove as this can cause the stove to emit fumes

into the room.

Chimney – Chimney Connection – Flue Diameter 125 mm

In order for the stove to perform satisfactorily the chimney height must be sufﬁcient to ensure an adequate

draught so as to clear the products of combustion and prevent smoke problems into the room.

IMPORTANT: Once the stove is unpacked and checked it is necessary to remove the central bar from the ﬂue collar of

the stove before installation. To remove unbolt collar remove bar and replace collar.

WF32/UNIQ32 INSET

Tested Draft 12pa

Max Draft 25pa

Flue gas temperature 317°C

Flue gas ﬂow 7.7 g/sec

NOTE: The outlet from the chimney should be above the roof of the building in accordance with the provisions of

Building Regulations Approved Document J. If installation is into an existing chimney, then it must be sound and

have no cracks or other faults which might allow fumes into the house. Older properties, especially, may have

chimney faults or the cross section may be too large. Westﬁre Aps recommend the use of a solid fuel ﬂue lining

system for all installation into existing chimneys. All chimney systems must be used in accordance with Building

Regulations Approved Document J.

If there is no existing chimney then either a prefabricated block chimney in accordance with Building Regula-

tions Approved Document J or a twin walled insulated stainless steel ﬂue to BS 1856-1. These chimneys must be

ﬁtted in accordance with the manufacturer’s instructions and Building Regulations. A single wall metal ﬂue pipe is

suitable for connecting the stove to the chimney but is not suitable for using for the complete chimney. The con-

necting ﬂue pipe must have a minimum diameter of 125 mm and its dimension should be not less than the size

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Westfire WF32 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info