Bedienungsanleitung Westfire WF35 (Seite 10 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

813317

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

WESTFIRE · WF35

UNIQ 35

Standard

UNIQ 35

Pedestal

UNIQ 35

inset

Distance from front to centre of top ﬂue exit n/a n/a 335mm

Distance from rear to centre of top ﬂue exit 120mm 120mm n/a

Distance from ﬂoor to centre of external air intake 115mm 505mm 65mm

WESTFIRE WF UNIQ 35

Distance to combustible materials rear 200mm

Distance to combustible materials side 200mm

Distance to Combustible materials

Combustible materials should not be located where the heat dissipating through the walls of ﬁreplaces or ﬂues

could ignite it. Therefore when installing the stove in the presence of combustible materials due account must

be taken of the guidance on the separation of combustible material given in Building Regulations Approved

Document J and also in these stove instructions.

The minimum distances to ﬂammable materials are speciﬁed on the EN 13240 plate on the back of the stove.

Hearth

The hearth should be able to accommodate the weight of the stove and its chimney if the chimney is not indepen-

dently supported.

The WESTFIRE UNIQ 35 stove has been tested and are suitable to be installed on a 12mm non-combustible plate such

as Westﬁre 12mm glass plates or 20mm slate plates. Installation of all hearths should comply in size and construc-

tion so that it is in accordance with the provisions of the current Building Regulations Approved Document J.

The clearance distances to combustible material beneath, surrounding or upon the hearth and walls adjacent to the

hearth should comply with the guidance on the separation of combustible material given in Building Regulations

Approved Document J and also in these stove instructions.

If the stove is to be installed on a wooden ﬂoor, it must be covered with a non-combustible material at least 12mm

thick, in accordance with Building Regulations Approved Document J, to a distance of 30 cm in front of the stove and

15 cm to each side measuring from the door of the combustion chamber.

Combustion air supply

In order for the stove to perform efﬁciently and safely there should be an adequate air supply into the room in

which the stove is installed to provide combustion air. This is particularly necessary if the room is double-glazed or a

ﬂue draught stabiliser is operating in the same room as the appliance. The provision of air supply to the stove must

be in accordance with current Building Regulations Approved Document J. An opening window is not appropriate

for this purpose. Air inlets must be positioned in such a way that they cannot be blocked. An air inlet may be a vent

(the vent must be open and the capacity of the vent sufﬁcient when the stove is lit) or a fresh air system linked to

the stove.

The WESTFIRE UNIQ 35 are ﬁtted as standard with a closed air supply collar, this enables the stove to take all

combustion air (primary, secondary and tertiary) directly from outside with 80mm pipe from the stove.

There are no European rules regarding the minimum distance to non-ﬂammable walls, Westﬁre recommend leaving

a gap of at least 10 cm behind and to sides of stove.

FLUE AND AIR INTAKE POSITIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Westfire WF35 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info