Bedienungsanleitung Westfire WF44 (Seite 9 von 30) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

813309

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

WESTFIRE · WF 44 · WF 45 · WF 46 WESTFIRE · WF 44 · WF 45 · WF 46

WESTFIRE · WF 44 · WF 45 · WF 46

UNIQ 44 UNIQ 45 / UNIQ 46

Height 736 mm 950 mm

Width 477 mm 477 mm

Depth 374 mm 374 mm

Closed combustion yes Yes

WESTFIRE · WF 44 · WF 45 · WF 46

UNIQ 44 / UNIQ45 / UNIQ46 dimensions

STOVE PERFORMANCE & TESTING

Westfire UNIQ44/ UNIQ45/ UNIQ46 have been approved in accordance with EN 13240

PREPARATORY WORK AND SAFETY CHECKS

IMPORTANT WARNING

This stove must not be installed into a chimney that serves any other heating appliance. There must not be an extrac-

tor fan fitted in the same room as the stove as this can cause the stove to emit fumes into the room.

Chimney

Chimney Connection: Flue Diameter 125 mm

IMPORTANT: Once the stove is unpacked and checked it is necessary to remove the central bar from the flue collar of

the stove before installation. To remove unbolt collar remove bar and replace collar.

In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure an adequate

draught so as to clear the products of combustion and prevent smoke problems into the room.

Minimum draft: UNIQ44/ UNIQ45/ UNIQ46 stoves has been tested with a draft of

12 Pa. Maximum draft 25 Pa.

Flue gas flow 4.5 g/sec.

Flue gas temperature 249°C. approximately 12 Pa.

NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of the stove to the top of the

chimney should be satisfactory. Alternatively the calculation procedure given in BS 5854:1980 may be used as the

basis for deciding whether a particular chimney design will provide sufficient draught.

The outlet from the chimney should be above the roof of the building in accordance with the provisions of Building

Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other faults which might

allow fumes into the house. Older properties, especially, may have chimney faults or the cross section may be

too large i.e. more than 160 mm x 160 mm. Remedial action should be taken, if required, seeking expert advice,

if necessary. If it is found necessary to line the chimney then a flue liner suitable for solid fuel must be used in

accordance with Building Regulations Approved Document J.

Any existing chimney must be clear of obstruction and have been swept clean immediately before installation of

the stove. If the stove is fitted in place of an open fire then the chimney should be swept one month after instal-

lation to clear any soot falls which may have occurred due to the difference in combustion between the stove and

the open fire.

Stove model Weight

Nominal heat output

Wood Smokeless fuels

UNIQ 44 80 kg 5.0 KW N/A

UNIQ 45 / UNIQ 46 90 kg 5.0 KW N/A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Westfire WF44 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info