Bedienungsanleitung Wharfedale opus2 2 (Seite 19 von 20) (Englisch)

419407

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Delay and LFE Settings

Expanding the System

The purpose of delay is to enable surround and dialogue information to arrive at the listener’s ears at the same time as

the Front channels, even when the listening seat is in a non-ideal position.

Rear Delay: If the listening position is equidistant from the Front and Rear speakers, a low delay setting should be set.

The closer the listener is to the Rear speakers the higher should be the delay setting used,

Centre Delay: If the Centre speaker is level with (or slightly behind) the Front speakers, set the delay to zero. If the

Centre speaker is forward of the Front speakers, increase the delay.

In domestic systems the LFE channel typically feeds into the subwoofer. Where no subwoofer is used, the LFE

signal is combined with Front Channel information. When you set the LFE level at your AV processor, use care as the

powerful low frequencies can overload domestic loudspeakers.

If you hear popping or thumping noises coming from the front loudspeakers or subwoofer, immediately turn the AV

Processor's volume level down and then back off the LFE level. This should cure the problem. If it does not, back off

the volume level at the subwoofer (if you are using one) until the problem disappears.

Please read the relevant sections of your AV amplifier manual and familiarise yourself with the various issues. If you

are unsure, consult your dealer for help.

Dolby Labs, DTS and THX offer 6.1 and 7.1 formats which extend the 5.1 principle by adding one or two extra rear

effects channels. Although the precise configuration of these systems will depend on the capabilities of your processor

and you should be guided by those instructions, we would make some observations.

For most 6.1 and 7.1 formats, and especially Dolby ES the listening seat should not be too close to the rear wall.

Optimising the time delay so that information from all speakers arrives at the listening seat coherently is critical if the

benefits of these systems are to be fully realised. THX adjustments in particular need to be followed to the letter.

LFE:

Left Surround

Left Back

90º

110º

135º

150º

22º

30º

LFE

Centre

Right Back

Right Surround

Right Front

Left Front

Dolby Labs Recommended 7.1 Placement

(Single Back channel for 6.1 shown dotted)

Opus²

Operating Your Subwoofer

Check that all connections to the subwoofer have been properly made and that the main volume control is at minimum. Plug the

supplied power cord into the mains socket on the rear panel.

Plug in the mains plug and switch the power on. Now switch the subwoofer on with the rest of your system.

The subwoofer on/off switch has a rocker action; press the upper part to switch the equipment on and the lower part to switch it

off. When switched on the light above the power switch will glow and the subwoofer will be operational.

All control functions are carried out using the remote handset. The handset must be pointed at the subwoofer and be in line of

sight for it to operate.

Operating the Standby key brings the subwoofer in and out of Standby.

The preset light will not light

if no preset has been set up

or if a preset is over-ridden.

In Standby, the Volume,

Filter, Preset and Phase

indicators are extinguished.

Rear panel lights stay on.

Press the Volume

+ key to increase the

volume level. Press the

Volume - key to decrease

the subwoofer volume.

The volume range on the front panel display varies from (minimum) to (maximum).

Pressing the appropriate filter key will select the frequency at which the subwoofer

rolls off. The filter has steps at Off and 35Hz-85Hz in 10 Hz increments. When ‘OFF’ is selected the

subwoofer operates over its full designed range. Pressing other keys lowers the maximum operating

frequency. The Low Pass Filter value should be chosen having regard to the nature of the Front speakers

and programme material. Follow the Setup Notes on Page 11 and the instruction manual of your AV

processor (if used) for more guidance.

This key toggles the subwoofer between 0º and 180º phase shift.

Four different settings of level, frequency and phase can be stored. Pressing and holding any of

the preset keys on the remote for 3 seconds will cause the current settings to be stored in that preset.

The display will show the preset number then flash the preset number once to show it has stored the

preset. To change from one preset to another: Press a preset key on the remote for less than 3 seconds

to recall the settings of that preset. The display will show the preset number.

If you select a preset and then alter any aspect of the setup, the preset light will extinguish (as the setup

no longer matches the preset).

When brought out of standby for the first time, the unit will display the factory presets. Thereafter, bringing the unit out of

standby will revert it to the operational state last used. If you switch the power on and off at the rear panel while the unit is in

standby, the unit will power up to a normal operating state (i.e. not in standby). To enter standby, again press the Standby key.

When you bring the unit out of Standby or perform any operation using the handset the

front panel lights will indicate the current setup and volume. After 10 seconds the lights will extinguish and the panel will go dark.

and the purpose is to minimise any distraction from the programme in play. The light above the mains power

switch on the rear panel will always remain illuminated whenever the subwoofer is switched on at the mains.

Operation

Standby:

Volume:

Low Pass Filters:

Phase:

Presets:

Note:

A Note on the Front Panel indicators.

This is intentional

00 99

OFF

LOW PASSFILTER SELECT

85Hz75Hz65Hz55Hz

45Hz

35Hz

MEMORY

POWER

PHA SE

180

1 2

VOLUME

Opus²

Wharfedale opus2 2 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info