Bedienungsanleitung Whirlpool ADN 230-2 (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

709121

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

1 ― ON / OFF SWITCH FOR INTERIOR LIGHT. On / off switch for interior light I -(ON)

O –(OFF)

4 ― ELECTRICITY SUPPLY INDICATOR. When the appliance is connected to the

electricity supply, the green indicator light is illuminated.

INSTALLATION AND OPERATING CONDITIONS OF THE

APPLIANCE

Preparing the appliance for operation

It is recommended to prepare the appliance for operation with a helper.

• Remove package. Lift the appliance away from foamed polystyrene base.

• Therefore take out adhesive tapes from sides and simply lift the appliance up and

take out the board. Strip adhesive tapes off and open the door. Remove the spacer

above the door.

• When positioning the appliance in chosen location, it will move more easily into

position if you lift the front a little and incline it backward allowing it to roll on its

casters. When placing, moving, lifting the appliance, do not hold the door

handles, do not pull the condenser at the rear part of the refrigerator and

do not touch the compressor unit.

• Take two supports from the bag and insert them into the guides at the top back part

of the appliance (see fig. 2, page 1).

If the appliance is brought in from the cold (temperature is not higher than +12

°C), you should wait for two hours before connecting it to the mains.

The appliance should not be connected to the mains until all packing and

transport materials aren’t removed. Suitably dispose the packaging material.

Positioning

• Place the appliance in a dry, well ventilated room.

WARNING! The appliance should not be operated in an unheated room or

porch. Place the appliance away from heat sources such as kitchen

stove/oven, radiators, or direct sunlight.

WARNING! The appliance must not touch any pipes for heating, gas or

water supply or any other electrical devices.

• Do not cover the ventilation holes at the top of the appliances – it must be a good air

circulation around the appliance. There should be a gap of at least 10 cm between

the top of the appliance body and any furniture that may be above it. If this

requirement is not followed, the appliance consumes more electrical energy and its

compressor may overheat.

• If the appliance is placed in a corner, a gap of at least 1 cm must be left between the

appliance body and the wall (see fig. 3, page 1).

• The appliance must stand on a level surface and must not touch the wall. If

necessary, regulate the height of the appliance by adjusting the levelling feet: by

turning them clockwise – the front of the appliance rises, by turning them counter

clockwise – it comes down. If the appliance is tilted slightly backward – the doors will

close by themselves.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool ADN 230-2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info